SEA ISUZU FSR Скачать руководство пользователя страница 49

Страница: 49 / 56

OWNER

’

S MANUAL

(

SEA ISUZU FSR/FSD EV)

SEA-OWS-QA-004/5

ISSUE DATE:

30/05/2020

Page

Cable is connected but no
mains power supply detected.
(It will turn to White-Red after 2
seconds which shows an error)

Check Mains Power Supply
availability and circuits.

Cable is not properly connected.

Check that the cable
connector is fully engaged
in the vehicle side socket.

White

Unlit

Green

Cable is connected.

Batteries are fully charged.

Unlit

After charge complete:

Both LED's turn to Unlit to
prevent any power drain of the
LV batteries.

Remove the cable from the
vehicle side socket.

White

Unlit

Red

Cable is connected but no
mains power supply detected.
(It will turn to Unlit-Red after 5-
10 seconds which shows an
error)

Check Mains Power Supply
availability and circuits.

Flash

Green

Cable is connected.

Vehicle is charging.

Unlit

Red

Cable is connected but no
mains power supply detected.
(It may turn to Unlit-Unlit after
some time)

Check Mains Power Supply
availability and circuits.

Apr 2020

LED Colour

Left

Right

Safe Operating Procedure

Note

Photo

Status

SEA-Drive® Charging Procedure (Two-LED Function)

SOP NO.

SOP-SD-006

Rev

Page

4/ 4

Model

SEA-Drive®

Variation

AS/NZ Trucks

Issue Date

Содержание ISUZU FSR

























































Результаты поиска

Содержание ISUZU FSR

Отзывы:

Похожие инструкции для ISUZU FSR

Бренды по названию

Популярные бренды

SEA ISUZU FSR, Руководство пользователя

Результаты поиска

Содержание ISUZU FSR

Отзывы:

Похожие инструкции для ISUZU FSR

Бренды по названию

Популярные бренды