manualshive.com logo in svg

SEA USA USER 2 - 24V, Руководство пользователя

Поделиться
Скачать
SEA USA USER 2 - 24V Скачать руководство пользователя страница 13

SELECTION OF THE SETTINGS

         The adjustments of the control unit are executed through the buttons "MENU"   and "SET” .
Pressing the "MENU” button you select the Leds corresponding to the various functions to be set, pressing the “SET” button you select the leds 
corresponding to the desired values inside every single function.

Selecting 

LED 12

 with the“

MENU

"   button   you enter into pausing time regulation, with 

LED 12

 turned on,   hold pressed the selected button   "

SET

” for the desired   

time of pause.   According to the colour that the leds 19, 20 and 21 will assume it will be possible to have an order of   the length of the set time of pause. If the button 
is released and   pressed again the time of pause will be annulled.     

Led L19 green turned on Time of pause <15 S.     
Led L20 yellow turned on Time of pause <45 S.       
Led L21 red turned on Time of break >45 S. up to 180 S.

Selecting 

LED 16

 with the “

MENU

" button you enter into the opening leaf delay adjustment, with 

LED 16

 turned on,   press the button   "

SET

” till to select the 

desired leaf delay, observing the colour of the leds 19, 20 and 21.

Led L19 green turned on leaf delay OFF   
Led L20 yellow turned on leaf delay <4 S.   
Led L21 red turned on leaf delay   >4 S. up to 12 S.

Selecting 

LED 17

 with the “

MENU

" button   you enter into the choice of the functioning logics, with LED 17 turned on, press the button "

SET

” till to select the 

desired logic, observing the colours of the Leds 19, 20 and 21.

Led L19 green turned on manual   logic   
Led L20 yellow turned on automatic logic
Led L21 red turned on security logic
Led L19 and L20 green and yellow turned on semi-automatic logic.

Selecting

 LED 22

 with the “

MENU

"button   you enter into the choice of the motors' speed, with LED 22 turned on, press the button "

SET

” till to select the desired 

speed, observing the colours of the leds 19, 20 and 21. 

Led L19 green turned on slow speed
Led L20 yellow turned on middle speed
Led L21 red turned on high speed
Hold pressed “SET” for more then 5 seconds to annul the executed number of cycles 

Selecting 

LED 10

 and 

LED 12 

(with alternate flashing) with   the “

MENU

” button   you enter into the motor torque adjustment.   With 

LED 10 

and 

LED 12

 flashing 

alternatively keep pressed the button “

SET

” while selecting the desired torque observing the color of the 

LEDS 19

, 

20

, 

21

.

Led L19 green turned on, torque = Low
Led L20 yellow turned on,   torque = Middle
Led L21 red turned on,   torque = Middle high   
Led L19, L20 and L21 turned on, troque = High

Selecting 

LEDS 22

 and 

17

 (with alternate flash) with the “

MENU

” button you enter into the choice of the type of motor that you are using.   

Note: In default the control unit is set on the 

FLIPPER

 motor. 

Led 19 green Alpha and Field 
Led 20 yellow Beta   
Led 21 red Flipper   
MENU HIDRO
LED19 Hydraulic
LED20 Barrier

 

After 30 seconds without having pressed any button, the parameters' adjustment function will be automatically left. 
If the control unit turns on when holding pressed the buttons “MENU” and “SET” contemporarily, the control unit will   start with the DEFAULT   
parameter   (see preceding page).

JOLLY function: With the JOLLY programmer it is possible to adjust linearly this parameter without using the MENU and SET buttons. 

JOLLY function: With the JOLLY programmer it is possible to adjust linearly this parameter without using the MENU and SET buttons. 

JOLLY function: With the JOLLY programmer it is possible to select the logic   without using the MENU and SET buttons on the control unit. 

JOLLY function: With the JOLLY programmer it is possible to select the speed without using the MENU and SET buttons on the control unit. 

JOLLY function: With the Jolly programmer this parameter is adjustable linearly for every single motor and differentiable within opening and 
closing without using the SET and MENU buttons on the control unit. 

JOLLY function: With the Jolly programmer it is possible to select the motor type without using the SET and MENU button on the control unit.

67410925

13

USER 2 - 24V 

International registered trademark n. 2.777.971

LED10

LED19

LED20

LED21

SET

MENU

LED17

LED22

LED16

LED15

LED12

GREEN

 YELLOW

RED

Programming 

LOGICS

SPEED

LEAF DELAY

TX LEARNING.

SELF LEARNING

PAUSE

REV 02 - 06/2010

Содержание USER 2 - 24V

























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды