Sea-doo 2001 GS 5548 Скачать руководство пользователя страница 56

Страница: 56 / 100

Carburetor-Equipped Models

Crank the engine a few turns to distrib-
ute the oil on cylinder wall.

RFI Models

Remove safety lanyard from its switch.

Depress the throttle lever at full throt-
tle position and hold.

Reinstall the safety lanyard cap on its
switch.

Crank the engine a few turns to distrib-
ute the oil on cylinder wall.

NOTE:

Proceeding in this order, no

fuel will be injected into the engine.

All Models

Apply anti-seize lubricant on spark plug
threads then reinstall them.

Reinstall plug on air intake silencer
cover.

Properly reconnect spark plug cables
to spark plugs.

Wipe up any residual water from the
engine.

Anticorrosion Treatment

To prevent corrosion, spray a corrosion
inhibitor (salt water resistant) such as
BOMBARDIER LUBE lubricant or
equivalent over metallic components
in engine compartment.

Apply dielectric grease (salt water re-
sistant) on battery posts and cable
connectors.

CAUTION:

Never leave rags or tools

in the engine compartment or in the
bilge.

smo2001-002a.book Page 54 Wednesday, June 7, 2000 3:57 PM

www.SeaDooManuals.net

Содержание 2001 GS 5548





































































































Результаты поиска

Содержание 2001 GS 5548

Отзывы:

Похожие инструкции для 2001 GS 5548

Бренды по названию

Популярные бренды

Sea-doo 2001 GS 5548, Руководство оператора

Результаты поиска

Содержание 2001 GS 5548

Отзывы:

Похожие инструкции для 2001 GS 5548

Бренды по названию

Популярные бренды