manualshive.com logo in svg

Sea-doo 2001 GS 5548, Руководство оператора, Страница: 43 / 100

Поделиться
Скачать
Sea-doo 2001 GS 5548 Скачать руководство пользователя страница 43

41

Hull

Inspect hull for cracks or damage.

Jet Pump Water Intake

Remove weeds, shells, debris or any-
thing else that could restrict the flow
of water and damage cooling system
or propulsion unit. Clean as necessary.
If any obstruction can not be removed,
refer to an authorized Sea-Doo dealer
for servicing.

TYPICAL

1. Inspect this area

Inspect leading edges of the impeller,
if they have nicks or bends perfor-
mance will be greatly reduced.

Bilge

Should water be present in the bilge,
tilt the watercraft to the rear and un-
screw drain plugs to completely empty
the bilge.

Secure bilge drain plugs.

Battery

Fuel Tank and Oil Reservoir 

With the watercraft horizontal, fill the
fuel tank to specified level.

Check the oil level and refill reservoir
as necessary.

Check fuel tank and oil reservoir retain-
ing straps/fasteners.

Engine Compartment

Steering System

Assisted by another person, check
steering operation for free movement.
When the handlebar is horizontal, the
jet pump nozzle should be in the
straight ahead position. Ensure the jet
pump nozzle pivots easily when han-
dlebar is turned.

Throttle System

Check throttle lever for free and smooth
operation. It should return to its initial
position immediately after it is released.

CAUTION

: Engine can be flooded if

throttle lever is applied several
times when engine is not running. If
engine is flooded, it will not start.

WARNING

Verify tightness of battery cables
to their posts and condition of re-
taining straps/fasteners.

F01J3ZY

1

WARNING

Should any leak or gasoline odor
be present, do not start the engine.
Refer to an authorized Sea-Doo
dealer before use.

smo2001-002a.book  Page 41  Wednesday, June 7, 2000  3:57 PM

www.SeaDooManuals.net

Содержание 2001 GS 5548





































































































Отзывы:

Нет отзывов