Sea-doo 2001 GS 5548 Скачать руководство пользователя страница 31 | Manualshive

Страница: 31 / 100

background image

29

7) Shift Lever

(if so equipped)

A 3-position lever:

– forward

– neutral

– reverse.

CAUTION:

Never rev the engine at

high RPM in reverse.

GTS Models

When pushed in, the watercraft is in
forward. To obtain neutral, unlock lever
by turning it counterclockwise, then
pull lever until neutral mark appears on
rod. To engage reverse, repeat same
procedure as for neutral, but pull lever
until reverse mark appears on rod. Le-
ver locks in forward and in neutral po-
sitions only.

8) Fuel Gauge/Low Oil

Warning Light
(if so equipped)

Analog gauge indicates the amount of
fuel in the fuel tank and a warning light
when level is low in oil reservoir.

1. Low oil warning light

NOTE:

With the safety lanyard discon-

nected, electrical system can be acti-
vated for approximately 33 seconds by
depressing the engine start/stop but-
ton.

9) Speedometer

(if so equipped)

Analog speedometer indicates the
speed of watercraft in miles per hour
(MPH) and kilometers per hour (km/h).

The speed sensor mounted on the ride
plate sends the signal to the speedom-
eter (and info center

if so equipped

).

10) Info Center Gauge/

Buttons (if so equipped)

This is a LCD (Liquid Crystal Display)
multifunction gauge.

The MODE button is used to change
display functions.

The SET button is used to set or reset
a function.

It features the following functions:

GSX RFI Models

– clock

– tachometer

– speedometer

– peak speed

– average speed

– trip meter

– engine hourmeter

– water temperature

– chronometer

– VTS

(if so equipped)

– fuel level

– low fuel

– low oil

– low voltage

– overheating

– maintenance information.

WARNING

Shift lever should only be used
when the engine is idling and wa-
tercraft is completely stopped. Only
use reverse at slow speed and for
the shortest time possible. Always
ensure the path behind is clear of
obstacles, swimmers and children
playing in shallow water.

1

0

F01G07Y

1

smo2001-002a.book Page 29 Wednesday, June 7, 2000 3:57 PM

www.SeaDooManuals.net

«
...
29
30
31
32
33
...
»

Содержание 2001 GS 5548





































































































Отзывы:

Нет отзывов

Похожие инструкции для 2001 GS 5548

Platinum Fiesta

Бренд: Aquaglide Страницы: 7

Бренд: Bavaria Yachts Страницы: 37

Бренд: Bavaria Страницы: 29

Бренд: Bavaria Страницы: 44

Бренд: Tiara Yachts Страницы: 160

SWITCH 13 FT 2022

Бренд: Sea-doo Страницы: 206

Бренд: True Course Yachting Страницы: 28

1998 GSX Limited 5625

Бренд: Sea-doo Страницы: 11

Бренд: Sea-doo Страницы: 15

Бренд: Tahe Страницы: 20

Бренд: Bavaria Страницы: 26

Бренд: Bavaria Страницы: 30

Бренд: Bavaria Страницы: 43

Бренд: Bavaria Страницы: 49

Бренд: Baja Страницы: 82

Бренд: J/Boats Страницы: 52

Бренд: Pelican Страницы: 2

Бренд: Sea Ray Страницы: 78

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды