Sea-doo 2001 GS 5548 Скачать руководство пользователя страница 68

Страница: 68 / 100

Fuses

If an electrical problem occurs, check
the fuses. If a fuse is burnt, replace by
one of the same rating. Follow proce-
dures below.

CAUTION:

Do not use a higher rated

fuse as this can cause severe dam-
age. If a fuse is regularly burnt, refer
to an authorized Sea-Doo dealer.

GTS Models

Fuses are located in the electrical box,
mounted on the MPEM.

To access fuses, unclip and move
away electrical box from its seat.

Open the electrical box.

Remove fuse caps.

1. Fuse caps
2. Spare fuse holder
3. MPEM

Check fuse condition.

Make sure to properly close the fuse
cap.

Properly close the electrical box cover
making sure its seal is well positioned.

RFI Models

To access fuses on the Multi-Purpose
Electronic Module, open front storage
compartment cover and remove bas-
ket.

Locate MPEM on the left side of wa-
tercraft.

Unclip the fuse cover from the MPEM.

TYPICAL

1. MPEM
2. Fuse cover

Use the tabs of the fuse cover to re-
move and reinstall fuses.

1. Fuse cover
2. Fuse tabs

NOTE:

There are 3 spare fuses on the

MPEM.

To access the fuses in the rear electri-
cal box, remove seats.

Remove basket.

F01H5IY

F06H1SY

F06H1TY

smo2001-002a.book Page 66 Wednesday, June 7, 2000 3:57 PM

www.SeaDooManuals.net

Содержание 2001 GS 5548





































































































Результаты поиска

Содержание 2001 GS 5548

Отзывы:

Sea-doo 2001 GS 5548, Руководство оператора, Страница: 68 / 100

Результаты поиска

Содержание 2001 GS 5548

Отзывы: