manualshive.com logo in svg

Sea-Bird Scientific SBE 25plus, Руководство пользователя

Поделиться
Скачать
Sea-Bird Scientific SBE 25plus Скачать руководство пользователя страница 33

Section 7 Maintenance

7.1 Corrosion precautions

N O T I C E

 

Blue Moly

™

 and Dow Corning

®

4 lubricants are electrically conductive. Keep away from electrical

components.

Flush the 25plus with fresh water after each use and before it is stored.
The stainless steel screws that connect the plunger switch to the end flange are
lubricated with a thick layer of Blue Moly

™

, and all other stainless steel screws that are

exposed to salt water are lubricated with a thick layer of Dow Corning

®

4. Remove and

lubricate all of these screws after each deployment.
The 25plus has a large zinc anode attached to each end flange. Make sure to examine
these at regular intervals to verify that they are securely attached and in good condition.
Replace when corrosion has reduced either one to less than 50%.
Do not attach metal objects directly to the pressure housing.

7.2 Plumbing

Clean the Tygon tubing at regular intervals to prevent clogged plumbing or air release
valve. To clean the air release valve:

1.

Remove the Tygon tubing above the air release valve and use needle-nosed pliers to
push a 0.4 mm diameter wire (or #26 AWG wire) through the valve hole.

2.

Blow air through the air release valve to make sure it is open.

3.

If necessary, replace the Tygon tubing above the air release valve.

7.3 Clean pressure sensor

N O T I C E

 

Do not put a brush or any object in the pressure port. It may damage or break the pressure
sensor.

31

Содержание SBE 25plus



































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды