SCP SCIENCE DigiPREP Скачать руководство пользователя страница 38

Страница: 38 / 88

SCP SCIENCE

KeyPad
Version 1.0

INSTALLATION

UNPACKING

Retain all packing material in case

you need to return the instrument

to the manufacturer for service.

Verify that all components listed have been

included:
•

Digi

PREP

block

• Operation

manual

•

Digi

PROBE

dongle

•

Digi

TUBE

rack

•

: 1 rack

•

: 2 racks

•

: 3 racks

•

: 0 racks

Optional items, such as glass, quartz,

calibrated or non-calibrated digestion

tubes may have been included in the

shipment. Carefully check the packing

list(s) and the contents of shipping

cartons to verify that all items

listed are included. Please notify

SCP

SCIENCE

or your local distributor of

any

discrepancies.

Inspect the products for any shipping damage.
If the instrument has been damaged in shipping,
contact the freight carrier to report damage and
to fi le a damage report. Also contact the

SCP

SCIENCE

service department to report damage

and to request service information (see page 88
for contact information).

If you fi nd evidence of damage, do

not attempt to operate the instrument.

SETTING UP

Place

the

Digi

PREP

block in a fume hood. The

controller must

not

be placed in the fume hood.

With the controller’s power switch in the “off”
position, do the following:

• Verify that the voltage selector at the back of the

Digi

PREP

block is properly set.(Typically 115 for

North America, and 230 for Europe.)
• Connect the block’s umbilical cable to the
controller.

Disconnecting or reconnecting the

umbilical cable while the controller is

turned on, especially while it is on the

RUN screen, will likely result in

permanent damage to the instrument.

• Connect the power cord to the back of the
controller

• Connect the

Digi

SET

(or

Digi

SET

dongle)

to the back of the controller.
• Connect

Digi

PROBE

(or

Digi

PROBE

dongle)

to the back of the block.

If you are not using the

Digi

PROBE

Digi

SET

, the dongles must be

connected; otherwise, an error message

may be displayed.

• Insert the glass well liner into the

Digi

PROBE

well.

(Small hole near right of block)
• If you are using

Digi

PROBE

, insert the

PROBE

into the well liner.

The system is now ready to be plugged in
and turned on. Please see your controller
manual for operation instructions.

NOTE

WARNING

Содержание DigiPREP

























































































Результаты поиска

Содержание DigiPREP

Отзывы:

Похожие инструкции для DigiPREP

Бренды по названию

Популярные бренды

SCP SCIENCE DigiPREP, Руководство по обслуживанию

Результаты поиска

Содержание DigiPREP

Отзывы:

Похожие инструкции для DigiPREP

Бренды по названию

Популярные бренды