Scotsman CME456R страница 34 Скачать руководство пользователя

Страница: 34 / 36

Removal and Replacement: Water Level Sensor

1. Remove front panel.
2. Push and hold the OFF button. Release it when

the machine stops.
3. Trace wire harness from water level sensor to

the Controller (#2). Unplug the harness from the

controller.
4. Lift the pump and mounting plate up enough to

remove the float from the stem.
5. Remove two screws holding the sensor to the

pump bracket and lift the sensor up and out of the

machine.
6. Reverse to reassemble.

Discharge Line Temperature Sensor

1. Remove front panel, push and release the Off

button.
2. Remove top and left side panels.
3. Locate discharge line sensor. It is attached to

the discharge line of the compressor, 6" from the

compressor discharge port.
4. Un-snap the clip holding the sensor to the

discharge line.
5. Trace the sensor wires back to the controller,

they are plugged into #5 with the water

temperature sensor, and must be replaced with it.
6. Reverse to replace, be sure that the discharge

line sensor is 6" up from the compressor discharge

port. The discharge line sensor is marked with

yellow tape.
Note: Route wires so they do NOT contact the

discharge line.

Water Temperature Sensor

Note: This sensor is replaced as a set with the

Discharge Temperature Sensor.
1. Remove left side and front panel.
2. Push and release Off button.
3. Remove 1 plastic bolt and the reservoir cover.
4. Locate water temperature sensor (inserted into

pump discharge hose).
5. Pull out to remove.
6. Trace back to AutoIQ Controller, unplug from

#5.
7. Remove the Discharge Line temperature

sensor.
8. Reverse to reassemble.
Note: Do not push sensor tip in too far. There

should be about an 1/8" gap between the tip and

the inner wall of the water discharge hose.

CME456R

December 2000

Page 34

Electrical Shock Hazard
Disconnect Electrical

Power Before Beginning

Содержание CME456R





































Результаты поиска

Содержание CME456R

Отзывы:

Похожие инструкции для CME456R

Бренды по названию

Популярные бренды

Scotsman CME456R, Руководство по эксплуатации продукта

Результаты поиска

Содержание CME456R

Отзывы:

Похожие инструкции для CME456R

Бренды по названию

Популярные бренды