Scotsman CME456R страница 29 Скачать руководство пользователя

Страница: 29 / 36

Service Diagnosis: Components

CME456R

December 2000

Page 29

Problem or Symptom Possible Cause

Probable Correction

Fan motor does not

turn.

Open motor windings, or

seized bearings

Replace fan motor

No power to fan motor

Contactor may not close.

Pump motor does not

turn

Open motor windings, or

seized bearings

Replace pump

No power to pump

Check electrical connections. In Freeze, the

pump should have power to it. If not, replace

the AutoIQ Controller.

Hot Gas Valve does

not open.

Open solenoid coil.

Replace hot gas valve

Stuck valve

Replace hot gas valve

No power to coil in Harvest Check wire connections, if ok, replace AutoIQ

Controller

Hot Gas Valve leaks

thru (warm tube

temperatures on both

sides of valve during

freeze)

Mechanical problem in

valve

Replace valve

Water Inlet Valve does

not open

Open solenoid coil

Replace valve

Stuck valve

Replace valve

No power to valve (best

checked at the beginning

of Freeze)

Check wire connections, if ok, replace AutoIQ

Controller

Water Inlet Valve does

not flow enough water

Restriction in water supply

Check water filters and/or inlet screen.

Water Inlet Valve

leaks thru

Mechanical problem in

valve

Replace valve

Compressor does not

work

Unit in Clean cycle

Push and release Freeze button.

Contactor coil open

Replace contactor

Open starting components Check and replace
Open windings

Check and replace compressor

Internal valve failure

Replace compressor

Содержание CME456R





































Результаты поиска

Содержание CME456R

Отзывы:

Похожие инструкции для CME456R

Бренды по названию

Популярные бренды

Scotsman CME456R, Руководство по эксплуатации продукта

Результаты поиска

Содержание CME456R

Отзывы:

Похожие инструкции для CME456R

Бренды по названию

Популярные бренды