Scotsman CME456R Скачать руководство пользователя

Страница: 28 / 36

Service Diagnosis

CME456R

December 2000

Page 28

Problem or Symptom Possible Cause

Probable Correction

Unit is off because of a

“Harvest Problem”

Ice sensors did not sense

ice falling, unit stayed in

harvest until the maximum

harvest time ran out.

Check ice sensors. If the bin full light is on or

blinking the bin controls may be dirty. Clean if

dirty. The board and bin controls may also

need to be checked.
Check evaporators for lime scale build up.

Clean evaporators and bin controls if dirty.
Push and release Off button. Push and

release Freeze button. Check machine

operation. Check if ice is made and harvests.

Bin controls or AutoIQ

Controller may have failed.

See “Unit does not shut off” below..

Other components may

have failed

Check the next page

Cubes are too large

Cube size control float is

sticking.

Check/clean

Inlet water valve leaking

thru (slowly)

Check hose from water valve for slow drip.

Replace valve if dripping.

Cubes are too small

Not enough water

Check for leak in reservoir
Check for a leak thru the purge valve

Low ice capacity

Dirty condenser

Clean condenser

Recirculation of air

Block air re-circulation or move condenser

Low refrigerant charge

Check system. If there is a low charge, find

the leak, recover the refrigerant, repair the

leak, replace the dryer, evacuate and weigh in

the nameplate charge.

Too much water

Check for inlet water valve leak thru

Unit does not shut off

Ice sensing system may

have failed.

Check controls. Unplug thermostat and check

bin full light, if off, place something between

the electric eyes. The bin full light should

begin to blink (after 20 seconds of continuous

blockage it will glow steadily). If not, check

operation of electric eyes by unplugging #4

and jumping out the two pins on the controller

(touch the tool to the cabinet to discharge

static electricity before contacting the

controller). If the bin full light blinks, replace

the bin controls. If it does not blink, replace

the controller. Note: Leaving #4 unplugged

and jumped for 20 seconds will shut the

machine down on a bin full (at the end of the

harvest cycle). It will restart after 4 minutes or

may be reset by pushing the Freeze button.

Содержание CME456R





































Результаты поиска

Содержание CME456R

Отзывы:

Похожие инструкции для CME456R

Бренды по названию

Популярные бренды

Scotsman CME456R, Руководство по эксплуатации продукта

Результаты поиска

Содержание CME456R

Отзывы:

Похожие инструкции для CME456R

Бренды по названию

Популярные бренды