Scotsman CME456R Скачать руководство пользователя

Страница: 22 / 36

Technicians Only: Harvest Cycle Sequence & Other Notes

Harvest

The Purge Valve will be open for 40 seconds.
The water pump shuts off, it will restart before 40

seconds, the restart time is based on the Purge

Level Setting.
The pump restarts and pumps water out of the

reservoir until the purge valve closes.
The inlet water valve will stay on for about 30

seconds to add enough water to assist with

harvest.
The Hot Gas Valve will be open for the entire

length of the Harvest Cycle.
The Harvest Bypass Valve will be open for a few

seconds (between 4 and 12, depending upon

discharge temperature) at the beginning of the

Harvest Cycle.
During the Harvest Cycle, ice will be falling from

the evaporators and between the ice sensor’s

electric eyes. The AutoIQ Controller monitors the

ice falling and uses that information to determine

the next harvest cycle length.
The first Harvest after a restart will take about 6

minutes to establish a base line, then the time it

took to release that ice is used to determine the

next harvest cycle’s length.
The maximum harvest time is 14 minutes.
If no cubes fall (or are sensed) by the end of the

Maximum Harvest Time, the machine senses a

Refrigeration error. If the next cycle also produces

a Refrigeration error, the machine will shut down.
Note: The last Harvest cycle before shutting off on

Bin Full will be about 6 minutes long.
Note: The machine will not restart for 4 minutes

after switching off on Bin Full, unless the Freeze

button is pressed.
Bin Full: The controller will switch on the

compressor for 30 seconds after 25 hours of off

time to keep refrigerant out of the compressor oil.
Continuous Run Time
A unit that operates 24 hours a day 7 days a week

is too small for the user’s needs. To maintain

harvest integrity, the controller will extend the

harvest time to 6 minutes every 15th consecutive

harvest cycle.

Bin Thermostat:

In normal ambients the thermostat will react to ice

on the bulb in a few seconds. Reaction after

removal will take about a minute under normal

conditions, and longer in colder rooms.

Diagnostic Light Code Table

If a Diagnostic

Light

Water Light

Refrigeration

Light

Blinks once and

repeats

Water pump will

not start

Very long ice

harvest

Blinks twice and

repeats

Lack of water fill No harvest of

ice

Blinks three

times and

repeats

not used

High Discharge

Temperature

Is ON all the

time

Water valve

leaking thru

rapidly

Check for low

discharge

temperature or

long freeze

cycle

Both ON all the

time

Check for thermistor set unplugged

or failed

Note: Diagnostic lights remain on until the

controller is manually reset or until it successfully

restarts the machine.

CME456R

December 2000

Page 22

Содержание CME456R





































Результаты поиска

Содержание CME456R

Отзывы:

Похожие инструкции для CME456R

Бренды по названию

Популярные бренды

Scotsman CME456R, Руководство по эксплуатации продукта

Результаты поиска

Содержание CME456R

Отзывы:

Похожие инструкции для CME456R

Бренды по названию

Популярные бренды