Scotsman CME456R страница 32 Скачать руководство пользователя | Manualshive

Страница: 32 / 36

background image

Removal and Replacement

Inlet Water Valve

1. Remove the front and left side panels.
2. Shut off the water supply.
3. Push and release the OFF button.
4. Pull the wire harness off the inlet water valve.
5. Remove screws holding the inlet water valve to

the back panel.
6. Pull the valve away from the cabinet and

disconnect the outlet tube.
7. Unscrew the water valve from the water inlet

tubing. Hold the barbed inlet fitting and rotate the

valve.
8. Reverse to reassemble.
9. Push and release the Freeze button.
10. Replace the front panel.

Water Pump

1. Disconnect the electrical power.
2. Remove the front panel.
3. Unplug water pump from its electrical

connection.
4. Remove 1 plastic bolt and the reservoir cover.
5. Lift water pump up and disconnect outlet tube.
6. Pull float ball from float stem (it is a snap fit).

Pull stem out.
7. Locate water level sensor mounting tabs,

compress together to release sensor from bracket.
8. Remove water pump brackets from pump.
9. Reverse to replace.
10. Replace front panel.
11. Re-connect electrical power.

Purge Valve

1. Disconnect electrical power.
2. Remove front panel.
3. Unplug wire harness from purge valve coil.
4. Locate and remove the two screws securing the

purge valve to the machine.

5. Pull the inlet and outlet hoses off the purge

valve and remove it from the machine.
6. Reverse to reassemble. There are no internal

parts available for this valve.

Purge Valve Timer

The purge valve timer is sensitive to electrostatic

discharge. Be certain to touch a grounded surface

before touching this component. Do the same

when handling the replacement part.
1. Touch a grounded surface.
2. Remove front panel.
3. Disconnect electrical power.
4. Remove high voltage box cover.
5. Locate timer board at the bottom of the high

voltage box.
6. Unplug all the wires to the board.
7. Compress each of the four stand-off posts to

release the board from the stand-offs.
8. Remove the board from the unit.
Reverse to reassemble.

Transformer and Compressor Starting

Components

Single phase compressors use a PTCR and run

capacitor. All are located in a sheet metal box to

the right of the AutoIQ Controller. The compressor

contactor is also located in that box.
1. Disconnect electrical power.
2. Remove front panel.
3. Remove 2 screws at the front edge of the metal

box, and pull the cover forward and out.
4. To check components, reconnect electrical

power.
Note: The contactor coil is 24 volt.

CME456R

December 2000

Page 32

«
...
30
31
32
33
34
...
»

Содержание CME456R





































Отзывы:

Нет отзывов

Похожие инструкции для CME456R

Бренд: LAVAZZA Страницы: 8

Бренд: Laspaziale Страницы: 44

Бренд: OFFNOVA Страницы: 10

Бренд: Brew Express Страницы: 20

Бренд: Mixpresso Страницы: 16

Бренд: Saeco Страницы: 66

Бренд: FRAM Страницы: 75

Бренд: Waring Страницы: 24

Бренд: Necta Страницы: 44

Бренд: Faber Страницы: 28

Magnifica ESAM6600

Бренд: DèLonghi Страницы: 19

Бренд: DeLonghi Страницы: 18

Бренд: brim Страницы: 20

Бренд: Lagrange Страницы: 32

Бренд: Toastess Страницы: 6

Бренд: MTN Products Страницы: 3

Бренд: Tupperware Страницы: 47

Бренд: Smach Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды