Scotsman BC0530 Скачать руководство пользователя страница 32

Страница: 32 / 42

BC0530 Service Manual

March 2020

Page 32

WATER PLATE REPLACEMENT

Turn off water and open plate until cams are in the

9:00 position then turn off the power.

2. Remove the control stream drain hose.
3. Remove water level probe assembly by sliding it

to the right beyond the control stream box and lift.

Disconnect tube assembly from main tank.

4. Remove the pump mounting screw holding the

water plate brace, the inlet, and outlet hoses from

the pump.

5.  Pry plastic hinge brackets away from the plate.
6.  Unhook the main springs from the water plate.
7.  Remove the screws that mount the control module

box. Pull the module forward to disconnect front

cam.

8. Slide the water plate and tank to the right without

turning and slide it forward out of the machine.

9. Remove the spring bosses, water plate brace,

water deflector, pressure pads and the four screws

holding the tank to the water plate. Remove

plastic bolt from shoulder on water plate and place

in new plate.

10. 1Attach the tank to new water plate with two #6

mach. screws on the left side and two #10 sheet

metal screws on the front and back.

Note: The speed nuts on the front and back holes are

no longer required.
11. 1With the open end of the water plate to the right,

slide it back into the machine and to the left of its

normal position.

12. Hook up the main springs to the water plate, rear

spring first.

13. Hook on and snap into place the plastic hinge

brackets

14. Secure the pump mounting screw holding the

water plate brace.

15. 15. Remove the water level probe assembly and

reposition the control stream drain tube. Position

and secure the control module box to mounting

bracket. Check adjustment of plastic lift bolt.

Reconnect harvest switch, if present.

16. Water plate must be aligned with the evaporator

per drawing illustration.

Содержание BC0530











































Результаты поиска

Содержание BC0530

Отзывы:

Похожие инструкции для BC0530

Бренды по названию

Популярные бренды

Scotsman BC0530, Руководство по обслуживанию

Результаты поиска

Содержание BC0530

Отзывы:

Похожие инструкции для BC0530

Бренды по названию

Популярные бренды