Scotsman BC0530 Скачать руководство пользователя страница 35

Страница: 35 / 42

BC0530 Service Manual

March 2020

Page 35

TROUBLE SHOOTING

Problem

Possible Cause

Solution

Ice machine is not

operating.

On-Off switch in “Off” position

Move switch to “On” position.

No power at ice machine. Circuit protector

open.

Replace fuse or reset breaker. Check

circuit for overload condition.

Ice machine off because bin is full of ice.

Use ice or move ice away from bin level

probe.

Ice machine off because bin level probe is

defective.

Replace bin level probe.

Ice machine off as if bin is full. Ambient

temp below 50°F (10°C).

Ambient temperature must be 60°F

(15°C) minimum.

Compressor is not op-

erating. Water pump

and other components

are operating normally.

See compressor test

procedure for more

information.

Ice-Clean switch in “Clean” position.

Move switch to “Ice” position.

High pressure cut-out open on air cooled

models. Condenser dirty.

Clean condenser and reset high pres-

sure cut-out. Confirm proper operating

pressures.

High pressure cut-out open on air cooled

models. Air circulation through condens

er is insufficient or hot air is recalculating

through the condenser.

Provide adequate spacing between the

ice machine and walls, ceilings or other

equipment. See installation instructions

for spacing requirements. Confirm prop

er pressures.

High pressure cut-out open on liquid

cooled models. Coolant liquid interrupted

or insufficient

Restore adequate coolant liquid supply

and reset high pressure cut out. Confirm

proper operating pressures.

High pressure cut-out open on liquid

cooled models. Interior of condenser has a

mineral build-up.

Clean or replace condenser.

High pressure cut-out open. Refrigeration

system is overcharged.

Remove refrigerant and recharge the

system to specifications.

Compressor thermal protector open be-

cause of low voltage condition.

Allow thermal protector to reset. Mea

sure voltage at contactor while com-

pressor is running. Correct power supply

problem if voltage is lower than specified

on the ice machine electrical plate. See

compressor test procedure for more

information.

Compressor thermal protector open be-

cause of defective run capacitor.

Replace run capacitor. See compressor

test procedure for more information.

Contactor is defective.

Check for voltage at coil terminals. Re

place contactor if it does not close when

the coil is energized.

Compressor start capacitor or relay defec-

tive

Test and replace these parts if defective.

See compressor test procedure for more

information.

Compressor is defective.

Replace compressor. See compressor

test procedure for more information.

Service Diagnosis

Содержание BC0530











































Результаты поиска

Содержание BC0530

Отзывы:

Похожие инструкции для BC0530

Бренды по названию

Популярные бренды

Scotsman BC0530, Руководство по обслуживанию

Результаты поиска

Содержание BC0530

Отзывы:

Похожие инструкции для BC0530

Бренды по названию

Популярные бренды