Scotsman BC0530 Скачать руководство пользователя страница 19

Страница: 19 / 42

BC0530 Service Manual

March 2020

Page 19

ALARM

CLEAN

MAKE ICE

FILL

FREEZE

LOWER

HARVEST

RAISE

HI WATER

LOW WATER

OVERFLOW

ARM UP

PLATE UP

ARM DOWN

BIN FULL

FULL RINSE

POWER

WATER LEVEL SENSOR

PROGRAMMING PORT

RESET

EVAPORATOR TEMP ADJUSTMENT

EVAPORATOR PROBE

BIN PROBE

BIN FULL ADJUSTMENT

SWITCH INPUT PORT

AC OUTPUTS

DUAL EVAPORATOR JUMPER

WATER RINSE JUMPER

FACTORY USE ONLY!

Machine Status:

Displays the position of the Ice/

Clean switch or an Alarm.

Sequence

: Displays the current stage of the ice

making process.

Input Status

: Displays the status of the individual

sensors for the ice making process.

Fault Codes:

The electronic control will monitor

for the following conditions and shut down the ice

machine as required to prevent damage to the

equipment.
>2

If the water tray automatically cycles 3 times

in a row due to a water plate obstruction the controller

will shut down the ice maker and provide LED fault

indicators.

After 3 consecutive failed attempts at raising the

water plate, the machine will defrost in 5 minutes then

try again. A 2 will flash during the 5 minute defrost.

Machine will shut down if it fails after this defrost

period.
>3

Flashes after 3 consecutive cycles over 35

minutes, But will not shut down the machine. Stops

flashing once a cycle is under 35 min.

Controller

Содержание BC0530











































Результаты поиска

Содержание BC0530

Отзывы:

Похожие инструкции для BC0530

Бренды по названию

Популярные бренды

Scotsman BC0530, Руководство по обслуживанию

Результаты поиска

Содержание BC0530

Отзывы:

Похожие инструкции для BC0530

Бренды по названию

Популярные бренды