Scotsman BC0530 Скачать руководство пользователя страница 21

Страница: 21 / 42

BC0530 Service Manual

March 2020

Page 21

Error-Code Troubleshooting

CODE:

FAULT CODE INDICATES: POSSIBLE CAUSE:

SOLUTION:

(Rev. 1.1/1.2/1.3)

Bad Evaporator Probe (shorted) or

wiring.
Hot Gas Valve stuck open Cuber

stuck in extended harvest mode.
Bad Control Board.
Actuator Motor won’t raise the

Water Plate.

Repair/replace wiring or replace

Probe.
Pull down the Water Plate and verify

the Hot Gas Valve closes after the

Water Plate closes. Repeat, with

power to the Hot Gas Valve coil

disconnected. If Hot Gas Valve does

not close, replace it.
Replace Control Board.
Replace Actuator Motor. (Motor

never raises Plate to actuate Plate

Switch, so HGV stays open & Evap

temp rises > 120F.

Evaporator temp over 120F.

(Rev. 1.1)

Cam Arm or Cam Pin is broken.
Cam Spring disengaged or broken.
Plate-Up Switch stuck open or not

actuating.
Over-freeze causing ice to stick to

water plate.
Silicone coating on Water Plate

worn away.
During harvest, the Evaporator

Probe is out of adjustment (reads

too warm) or is defective.
Arms-Up Switch stuck closed- Plate

stays down.
Bin Probe is out of position

Replace Cam Arm or Cam Pin.
Reinstall springs or replace as

needed.
Adjust switch actuator or replace as

needed. Check to ensure that the

Plate-Up switch actuates before the

Arms-Up switch actuates.
Lower the short water level probe, in

1/16” increments, until cubes have a

pea-sized dimple in the center.
Replace the Water Plate if the

factory coating is severely worn

and is causing ice to stick to it.

Use a Food-Grade Silicone spray

to provide a temporary improved

surface, until the water plate can be

replaced.
Adjust Evaporator Probe colder

(turn CW), or replace if adjustment

does not help.
Free up, adjust or replace stuck/

shorted Arms-Up Switch, or repair

wiring.
Re-position or replace Bin Probe.

Water Plate failed to close

after three consecutive

attempts.

(Rev. 1.2/1.3)
After 3 attempts to close,

machine goes into a

30-minute shutdown, with

the Plate open. It will repeat

this routine (w/ the Plate

closing 3 times & then a

30-minute wait) four times,

before going out on Code

20.
The Code 20 LED will

flash

as this routine is in process,

and then light solid after the

routine tries 4 times and

ends Code 20.

Содержание BC0530











































Результаты поиска

Содержание BC0530

Отзывы:

Похожие инструкции для BC0530

Бренды по названию

Популярные бренды

Scotsman BC0530, Руководство по обслуживанию

Результаты поиска

Содержание BC0530

Отзывы:

Похожие инструкции для BC0530

Бренды по названию

Популярные бренды