manualshive.com logo in svg

SciCan HYDRIM C15wd, Руководство по обслуживанию

Поделиться
Скачать
SciCan HYDRIM C15wd Скачать руководство пользователя страница 21

View IO Status: Shows the status of the each component in the unit

Chamber Full SW - ON/OFF  (chamber full switch)
Salt SW - ON/OFF (salt switch)
Rinse Aid - ON/OFF (not used)
Chemical Sensor - ON/OFF
Chamber Overflow ON/OFF
Chamber Pressure - ON/OFF
Door SW ON/OFF  (Door switch)
Chamber T - XX C  (chamber temperature)
Validation T - XX C  (validation temperature)
CTS - ON/OFF (clear to send to printer/ datalogger)

Verify Mode: Automatically checks all components in sequence.

Set debug screen: Shows I/O status when cycle is running

Cycle Settings 

Set Drying Time

P1 Regular

10 min         (choose from 1 to 15 min)

P2 Heavy Duty

10 min         (choose from 1 to 15 min)

P3 HD Disinfection 

10 min         (only value accepted is 10)

Set Regeneration – Sets water softener setting

0         (choose from 0 to 3)

Chemical Set-up

Prewash

4s         (choose from 0 to 15s)

Wash

13s        (choose from 0 to 30s)

High Temp. Wash (second part of wash phase)

13s        (choose from 0 to 30s)

Rinse / Disinfect 

13s        (choose from 0 to 15s)

Set Wash Time

P1 Regular

5 min        (choose from 5 to 15 min)

P2 Heavy Duty

9 min        (choose from 5 to 15 min)

P3 HD Disinfection 

9 min        (choose from 5 to 15 min)

6. Technical Service Menu

Page 20

HYDR

IM

C51wd Service Guide

Содержание HYDRIM C15wd













































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды