background image

12

 

PROBLEM

POSSIBLE CAUSE

REASON/SOLUTION

The charger is 

making an audible 

clicking sound.

Circuit breaker is cycling.

Battery is defective.

Shorted battery cables 

or clamps.

Severely discharged battery, but 

otherwise it is a good battery.

Reversed connections at battery.

The settings may be wrong. Check 

the charger settings.

Have the battery checked.

Circuit breaker cycles when current 

draw is too high. Check for shorted 

cables or clamps and replace if 

necessary.

The battery may not want to accept 

a charge due to a run-down state. 

Allow charging to continue until 

battery has a chance to recover 

sufficiently to take a charge. If more 

than 20 minutes, stop charging and 

have the battery checked.

Shut the charger off and correct the 

lead connections.

Charger makes a 

loud buzz or hum.

Transformer laminations vibrate 

(buzz).

Shorted Diode Assembly or 

Output Rectifier Assembly (hum).

No problem; this is a normal 

condition.

Have charger checked by a qualified 

technician.

Short or no start 

cycle when cranking 

engine.

Drawing more than the engine 

start rate.

Failure to wait 3 minutes  

(180 seconds) between cranks.

Clamps are not making a good 

connection.

AC cord and/or extension cord 

is loose.

No power at receptacle.

The charger may be 

overheated.

Battery may be severely 

discharged.

Crank time varies with the amount 

of current drawn. If cranking draws 

more than the engine start rate, 

crank time may be less than 3 

seconds.

Wait 3 minutes of rest time before 

the next crank.

Check for poor connection at battery 

and frame.

Check power cord and extension 

cord for loose fitting plug.

Check for open fuse or circuit 

breaker supplying AC outlet.

The thermal protector may have 

tripped and needs a little longer to 

reset. Make sure the charger vents 

are not blocked. Wait and try again.

On a severely discharged battery, 

charge for 10 to 15 minutes at 

the lowest rate, to help assist in 

cranking.

The measured 

current is much 

lower than what was 

selected.

The charger reached the 

maximum voltage and is 

reducing the current.

No problem; this is a normal 

condition.

Содержание SE-2352












Отзывы: