background image

OPERATION

FX-742   07/16

Operation Section 4-43

© 2016 Alamo Group Inc.

OPERA

T

ION

After the driveline has been removed from the
tractor, place the PTO master shield back in the
operating position.

13. MOWER STORAGE

It is recommended that the mower be stored with the center section and both wings fully lowered to ground
level.  If the mower is stored with the wings in the raised position, select a level area and install wing transport
braces to prevent the wings from falling BEFORE disconnecting the mower hitch from the tractor.

Properly preparing and storing the mower at the end of the season is critical to maintaining its appearance
and to help ensure years of dependable service.  The following are suggested storage procedures:

Thoroughly clean all debris off the mower to
prevent damage from rotting grass and
standing water.

Lubricate all mower grease points and fill
gearbox oil levels as detailed in the
maintenance section.

Tighten all bolts and pins to the recommended
torque.

Check the mower for worn and damaged
parts.  Perform repairs and make
replacements immediately so that the mower
will be ready for use at the start of the next
season.

Store the mower in a clean, dry place with the
mower housing resting securely on blocks or
at ground level.

Keep the driveline yoke from sitting in water,
dirt and other contaminants.

Use spray touch-up enamel where necessary
to prevent rust and maintain the appearance of
the mower. 

It is critical that driveline clutches slip when an obstacle or heavy load is encountered to avoid mower and/or
tractor damage. If the mower sits outside for an extended period of time or is exposed to rain and/or humid air,
the clutch lining plates must be inspected to ensure they are not frozen together from rust or corrosion.  If the
mower has been exposed to such conditions, at the start of each mowing season, and any time it is suspected
that the slip clutch plates may be frozen together, readjust the slip clutch as detailed in Seasonal Clutch
Maintenance of the maintenance section in this manual.  

OPS-R-0032_I

Содержание FX-742









































































































































































Отзывы: