schmersal PSC1-C-10 Series Скачать руководство пользователя страница 137

Страница: 137 / 173

Installation manual

PSC1-C-10 Installation manual V2.6

Page 137 of 173

Version: 57E

Maintenance

9.1

Modification / dealing with changes to the device

Servicing work is only allowed to be undertaken by qualified personnel.
It is not necessary to undertake regular servicing work.

Repair

Devices are always to be replaced completely.
It is only possible to repair a device in the factory.

Warranty

The warranty will be rendered void if the module is opened without authorisation.

Note:

The modification of the module will render void the safety approval!

9.2

Replacement of a module

On the replacement of a module the following should be noted:

•

Disconnect power converter from the main supply.

•

Switch off power supply for the device and disconnect.

•

Disconnect encoder connector

•

Remove all other plug-in connections.

•

Remove module from the DIN rail and correct correctly in relation to EMC.

•

Fit new module to the DIN rail.

•

Restore all connections.

•

Switch on power converter.

•

Switch on supply voltage.

•

Configure device

Note:

In principle, no plug-in connection on the PSC1 module is allowed to be disconnected or connected
again while electrically live. In particular, there is a risk of irreparable damage to position or speed
sensors connected.

9.3

Servicing interval

Module replacement

See technical data

Function test

See section Commissioning

Содержание PSC1-C-10 Series














































































































































































Результаты поиска

Содержание PSC1-C-10 Series

Отзывы:

Бренды по названию

Популярные бренды

schmersal PSC1-C-10 Series, Руководство по установке

Результаты поиска

Содержание PSC1-C-10 Series

Отзывы:

Бренды по названию

Популярные бренды