background image

7

EN

EX-CSS180-D-EN

EX-CSS 180

Operating instructions

Safety sensor

8.  EU Declaration of conformity

Name of the component:

EX-CSS 180  

L

 II 3G Ex nA IIC T6 Gc X

L

 II 3D Ex tc IIIC T70°C Dc X

Type:

See ordering code

Description of the component:

Non-contact safety sensor

Relevant Directives:

Machinery Directive

EMC-Directive

Explosion Protection Directive (ATEX)

RoHS-Directive

2006/42/EC

2014/30/EU

2014/34/EU

2011/65/EU

Applied standards:

DIN EN 60947-5-3:2014,

EN 60079-0:2012 + A11:2013,

EN 60079-15:2010,

EN 60079-31:2014

Notified body, which approved the full 

quality assurance system, referred to in 

Appendix IV, 2014/34/EU:

TÜV Rheinland Industrie Service GmbH

Am Grauen Stein

51105 Köln

ID n°: 0035

Person authorised for the compilation  

of the technical documentation:

Oliver Wacker

Möddinghofe 30

42279 Wuppertal

Place and date of issue:

Wuppertal, May 2, 2017

Authorised signature

Philip Schmersal

Managing Director

EU Declaration of conformity

Original

K.A. Schmersal GmbH & Co. KG

Möddinghofe 30

42279 Wuppertal

Germany

Internet: www.schmersal.com

We hereby certify that the hereafter described components both in their basic design and construction conform 

to the applicable European Directives. 

The currently valid declaration of conformity can be  

downloaded from the internet at www.schmersal.net.

Содержание EX-CSS 180









Отзывы: