Schlage KING COBRA-2 KC5196-2-R Скачать руководство пользователя | Manualshive

Страница: 6 / 28

background image

KC9111/KC9111-2 & KC9321/KC9321-2 INSTALLATION

Installing the KC9111/KC9111-2 or KC9321/KC9321-2

57040-E Page 6 04-2007

Installing the KC9111/KC9111-2 or KC9321/KC9321-2

Installing the KC9111/KC9111-2 or KC9321/KC9321-2

If your trim has a key cylinder already installed, skip to

Determine Hand: on page 12

. Other-

wise, continue with

Loosen the Baseplate Screws: on this page.

1) Loosen the Baseplate Screws:

2) A Key Cylinder That Is At Least 1-1/8” Long Must Be Installed:

IMPORTANT: Do not remove any of the screws in the fol-
lowing step or it will be difficult to reinstall them.

•

Using a small Philips head screwdriver,

loosen

screws

a

&

b

in baseplate, around key cylinder

hole, one turn.

NOTE: Screws a, b, c & d are set at the factory.
Screws a & b are tightened and screws c & d are left loose.

b

d

a

c

> The key cylinder that you install must be 1-1/8” long or longer.

>>>> Do not attempt to install a key cylinder that is shorter than 1-1/8”

> The two illustrations below show the difference between a 1” and a 1-1/8” key cylinder.

1” long key cylinder.

DO NOT ATTEMPT TO INSTALL A 1”
LONG KEY CYLINDER.

1-1/8” long key cylinder

ONLY INSTALL A KEY CYLINDER
THAT IS AT LEAST 1-1/8” LONG.

«
...
4
5
6
7
8
...
»

Содержание KING COBRA-2 KC5196-2-R





























Отзывы:

Нет отзывов

Похожие инструкции для KING COBRA-2 KC5196-2-R

Бренд: danalock Страницы: 3

Бренд: danalock Страницы: 8

Бренд: danalock Страницы: 32

Бренд: danalock Страницы: 24

Бренд: danalock Страницы: 20

V3 BT HK SCANDI

Бренд: danalock Страницы: 17

Бренд: danalock Страницы: 13

Бренд: Hama Страницы: 9

MORTISE 8800 SERIES

Бренд: Yale Страницы: 54

Бренд: Zap Страницы: 2

DEADBOLT EDITION SECURE PGD728

Бренд: Lockly Страницы: 17

Adhesive Magnet Lock

Бренд: Qdos Страницы: 12

Бренд: Hama Страницы: 4

Бренд: Schlage Страницы: 12

Бренд: Nice Страницы: 28

TSA Zipper Lock

Бренд: Conrad Страницы: 2

Passport 1000 P2

Бренд: Sargent Страницы: 17

Бренд: KFV Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды