Scheppach 5903815900, Перевод оригинального руководства пользователя

Страница: 27 / 92


www.scheppach.com /

service@scheppach.com /

+(49)-08223-4002-99 /

+(49)-08223-4002-58
GB | 27
For grinding or cutting wheels up to approx. 3
mm thick: Screw on the flange nut with the flat side
facing the grinding or cutting wheel.
10.3.2 Flange arrangements when using grinding
wheels and cutting wheels (Fig. 5)
• Mount guard (1), clamping flange (a), wheel (7) and
flange nut (b) as shown in Fig. 5
.
• The arrows indicate the mounting direction.
10.4 Motor
It is vital for the motor to be well ventilated during op -
eration. Be sure, therefore, to keep the ventilation
holes clean at all times.
10.5 Grinding wheels
• Never use a grinding or cutting wheel bigger than
the specified diameter.
• Before using a grinding or cutting wheel, check its
rated speed.
• The maximum speed of the grinding or cutting
wheel used must be higher than the idle speed of
the angle grinder.
• Use only grinding and cutting wheels that are ap -
proved for a minimum speed of 8,500 rpm and a
peripheral speed of 52 m/sec.
• Check the direction of rotation when you use dia -
mond cutting wheels. The directional arrow on the
diamond cutting wheel must point in the direction
in which the tool rotates.
Take special care that the grinding/cutting wheels
are properly stored and transported. Ensure that the
grinding/cutting wheels are never exposed to shock,
jolts or sharp edges (for example during transport
or storage in a toolbox). This could cause damage
(such as cracks) to the grinding/cutting wheels and
place the user in serious danger.
11. Operating instructions
When working with the device, always wear suit-
able clothing and appropriate protective equip-
ment. Prior to each use it must be ensured that
the device is working correctly. Personal protec-
tive equipment and a fully functional device re-
duce the risk of injuries and accidents.
11.1 Rough grinding
m
WARNING
Use the safety device for grinding
For the best rough grinding results, hold the grind -
ing wheel at an angle of between 30° and 40° to the
workpiece surface and guide back and forth over the
workpiece in steady movements.
11.2 Cutting
m
WARNING
Use the safety device for abrasive cutting
When you use the right-angle grinder for cutting pur -
poses, avoid tilting it in the cutting plane. The cutting
wheel must have a clean cutting edge. A diamond
cutting wheel is best used to cut hard stone.
m
It is prohibited to use the machine on asbes-
tos materials!
m
Never use a cutting wheel for rough grinding.
12. Cleaning, storage and
maintenance
m
WARNING
Always pull out the battery pack before starting
any cleaning work.
12.1 Cleaning
• Keep all safety devices, air vents and the motor
housing free of dirt and dust as far as possible.
Wipe the equipment with a clean cloth or blow it
with compressed air at low pressure.
• We recommend that you clean the device immedi -
ately each time you have finished using it.
• Clean the equipment regularly with a moist cloth
and some soft soap. Do not use cleaning agents
or solvents; these could attack the plastic parts of
the equipment. Ensure that no water can seep into
the device. The ingress of water into an electric tool
increases the risk of an electric shock.
12.2 Storage
Store the device and its accessories in a dark, dry
and frost-proof place that is inaccessible to children.
The optimum storage temperature is between 5 and
30˚C. Store the electrical tool in its original packag -
ing. Cover the electrical tool in order to protect it from
dust and moisture. Store the operating manual with
the electrical tool.
12.3 Maintenance
There are no parts inside the equipment which re -
quire additional maintenance.
Service information
Please note that the following parts of this product
are subject to normal or natural wear and that the fol -
lowing parts are therefore also required for use as
consumables.
Wear parts*: Grinding wheels
* Not necessarily included in the scope of delivery!
13. Disposal and recycling
The equipment is supplied in packaging to prevent it