background image

16 

h) Never use damaged or incorrect saw blade shims 
or screws.
The saw blade shims and screws are designed espe-
cially for your saw, for optimal performance and operat-
ing safety.

m

 

Additional safety instructions 

for all saws

Causes and prevention of kickbacks:

•  A kickback is a sudden reaction due to a caught, 

jammed or incorrectly adjusted saw blade, which leads 
to the saw rearing up in an uncontrolled manner and 
moving out of the work piece towards the operator.

•  If a saw blade catches or jams in the sawing edge that 

closes behind it, it is blocked and motor’s drive pushes 
the saw back in the direction of the operator.

•  If the saw blade twists in the saw groove or is incor-

rectly positioned, the teeth at the rear side of the saw 
blade edge catch in the surface of the work piece. The 
saw then moves out of the saw groove and springs 
back in the direction of the operator.

•  A kickback results from an incorrect or faulty use of the 

saw. It can be prevented, as will be described in the 
following, by appropriate cautionary measures. 

a) Hold onto the saw with both hands and position your 
arms so that they can absorb any energy from a kick-
back. Always keep to the side of the saw blade, and 
never bring it into line with your body. In the case of a 
kickback, the circular saw can jump backwards, but with 
adequate caution the operator can deal with the energy 
of the kickback.
b) If the saw blade jams or you want to interrupt your 
work, then turn the saw off and keep the work piece still 
until the saw blade comes to a full stop. Never try to re-
move the saw from the work piece or pull it out when the 
saw blade is moving since then a kickback can occur. 
Find out the cause of the jam and remove it. 
c) If you want to start up a saw that is in the work piece, 
centre the saw blade in the sawed groove and check that 
the saw blade teeth are not caught in the work piece. 
If the saw blade is jammed, it can jump out of the work 
piece or cause a kick back when it is started up.
d) Support larger work pieces in order to reduce the 
risk of a kick back due to a saw blade jam.  The weight 
of larger work pieces can cause them to bend. Large 
pieces must be supported on both sides, both near the 
sawing slot as well as on the edges.
e) Do not use dull or damaged saw blades. Saw blades 
with dull or misaligned teeth increase the friction, in the 
sawing slot, cause saw blade jams and kickbacks.
f) Before you start sawing, tighten the adjustments for the 
cut depth and angles. If you change settings while saw-
ing, the saw blade can jam and a kickback is the result.
g) Be particularly careful when making “insert-
ed cuts” in walls that already exist or other areas 
where you cannot see what is behind the surface.  

c) Disconnect the plug from the wall outlet before you 
make adjustments to the tool, change parts or put the 
tool away. This precaution prevents inadvertent start-
ups of the tool.
d) Store power tools that are not in use out of reach of 
children. Do not let anyone use the tool who does not 
have experience with it, or who has not read these in-
structions. Power tools can be dangerous when they are 
used by inexperienced people.
e) Take good care of your power tools. Make sure that 
movable parts function properly and do not jam, see 

that parts which influence the use of the machine are 

not broken or damaged. Repair damaged parts before 
operating the tool. Many accidents are caused by poorly 
maintained power tools.
f) Keep cutting edges sharp and clean. Properly main-
tained cutting tools with sharp cutting edges jam less 
often and are easier to control.
g) Use power tools, accessories, and equipment accord-
ing to these instructions. Taking into account the working 
conditions and the work being performed.
The use of power tools other than those intended for the 
tool itself can lead to dangerous situations.

5) Service

a) Only let qualified service personnel repair your tool 

and always use original replacement parts. This guaran-
tees that the power tool remains safe to use.

m

 

Safety instructions for all saws

a) DANGER: Do not put your hands in the sawing area 
or on the saw blade. Keep your second hand on the ex-
tra handle of the motor housing. If both hands are hold-
ing the saw, neither can be injured by the saw blade.
b) Do not put your hands under the work piece. The 
protective cap cannot protect your hands from the blade 
when they are under the work piece.
c) Adjust the cutting depth to the thickness of the work 
piece. Less than one complete sawing tooth should be 
visible under the work piece. 
d) Never hold the work piece that is to be sawn in your 
hand or over your leg. Make sure that the work piece 
has a stable balance. It is important that the work piece 
is held securely, in order to minimize the danger of con-
tact of a body part with the saw, loss of control over the 
saw, or jamming of the blade.
e) Hold the equipment on the insulated handles, when 
you undertake work in which the tool being used could 
come into contact with hidden electrical wires, or its own 
cable. Contact with a live power source can electrify the 
metal parts of the tool and lead to an electrical shock.
f) When making a long cut, always use a stop chock or a 
straightedge. This improves the accuracy of the cut and 
reduces the chance that the saw blade jams.
g) Always use the correct size of saw blades and make 
sure they have the right locating bore (e.g. Star shaped 

or round). Saw blades that do not fit the assembly of 

the saw do not run correctly and cause loss of control.

Содержание 5801804903

















































Отзывы: