Scanjet BIO 10 Скачать руководство пользователя страница 37

Страница: 37 / 40

#BIO10 11 – 140813

Page 37 of 40

Claim Report

Cleaning Media

Type of cleaning media? _________________________________

Clean

Contaminated with? ___________

Chemicals / Solvents ____________

Hard particles size ______________

Soft particles size ______________

Solidifying

Crystallizing

Is there a ﬁ lter installed in supply line? Mesh size __________________________

Is the tank cleaning machine ﬂ ushed with clean water after cleaning?

Type of tank contents to be removed

Type of sludge in the tank (name, formula, concentration etc) _______________

What is the sludge soluble in? __________________________________________

Nature of material:

Crystalline

Solidifying

Hard particles

Soft Particles

High Viscous

Low Viscous

Explosive

Sticky

Is the tank cleaning machine lowered into the material? ____________________

Other information

______________________________________________________

Date: ____________________________ Signature: __________________________

(2/2)

Содержание BIO 10









































Результаты поиска

Содержание BIO 10

Отзывы:

Scanjet BIO 10, Инструкция по эксплуатации, Страница: 37 / 40

Результаты поиска

Содержание BIO 10

Отзывы: