sauter RDT410 Скачать руководство пользователя страница 31 | Manualshive

Страница: 31 / 36

background image

SAUTER flexotron®400 - RDT410

Configuration

P100012103

31

0°C temperature boost

In control mode 4 an extra temperature boost can be added at 0°C outdoor
temperature. The boost recedes from the set value to 0 over ±3 degrees.

Supply temp

Outdoor temp

SP

H

SP

L

-20

0

+20

D-factor

Control mode 5, Domestic hot water temperature control is often a very difficult
application which calls for responsive control. The RDT410 therefore utilises PID-
control for this control mode. In this menu you set the D-factor (the derivative
factor).

Menus X.7
Universal input UI1 (Control modes 1, 2, 3)
Pump exercise (Control mode 4)
Periodic overheating (Control mode 5)

Input UI1

For control modes 1, 2 and 3 you can choose to configure the universal input UI1
as either an analogue input for a frost protection sensor on either output
(snowflake-symbol) in a water-heated system or as a digital input for a high
temperature limiting switch (sun-symbol) in an electric heater. It can also be set
to --, not active.
If set to frost protection sensor RDT410 will activate the frost protection function
and also shutdown mode, see chapter 5.
If set to high temperature limit switch, the fan will run for an extra 3 minutes after
the heating output has been turned off at shutdown.

Frost protection on AO1

Frost protection on AO2

High temp. limit switch

Not used

«
...
29
30
31
32
33
...
»

Содержание RDT410





































Отзывы:

Нет отзывов

Похожие инструкции для RDT410

Бренд: Veer Страницы: 2

Бренд: Jabra Страницы: 18

Бренд: Union Instruments Страницы: 63

Бренд: We Care Solar Страницы: 46

Бренд: Watts Страницы: 4

OneFlow OFTWH-R

Бренд: Watts Страницы: 8

Бренд: SYR Страницы: 2

Бренд: Insignia Страницы: 2

Бренд: Thermomart Страницы: 6

Бренд: TEL Страницы: 26

Бренд: Vimar Страницы: 32

Бренд: Whale Страницы: 8

Бренд: Tascam Страницы: 8

Бренд: Xilinx Страницы: 101

Бренд: Burkert Страницы: 21

Kerio Control Box NG510

Бренд: GFI Страницы: 4

Бренд: Vageo Страницы: 2

Бренд: DirectConnect Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды