manualshive.com logo in svg

Satec 3100 Series, Руководство пользователя

Поделиться
Скачать
Satec 3100 Series Скачать руководство пользователя страница 30

Series 3100

PP3123-03-0101

Automatic Burst Test Systems

User’s Guide

SATEC PIPE & PRESSURE

30

System Drainage for Long Term Storage

Draining the system will prevent sediment build up or freezing.  This section will
provide you with the procedures and methods needed to successfully drain the
system.  This equipment is designed to provide years of service if maintained
properly.

WARNING!

DO NOT store system where it may be subjected to below freezing
temperatures without proper draining.

To drain the system use the following procedure:

1.

 

Turn off main power.

2.

 

Disconnect the air supply.

3.

 

Shutoff and disconnect the water supply.

4.

 

Bleed off the pressure.  Slowly open the internal by-pass valve.

5.

 

Remove the water filter canister and drain water from it.  Replace the drained
canister.

6.

 

Connect an air supply to the water supply port.  Turn on air supply.

7.

 

Close the internal by-pass valve when the system is completely drained.

Содержание 3100 Series
































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды