manualshive.com logo in svg

Satec 3100 Series, Руководство пользователя

Поделиться
Скачать
Satec 3100 Series Скачать руководство пользователя страница 13

PP3123-03-0101

Series 3100

User’s Guide

Automatic Burst Test Systems

SATEC PIPE & PRESSURE

13

I

NTRODUCTION

WARNING!

If the equipment is used in a manner not specified by SATEC, the
protection provided by the equipment may be impaired.  Injury to
personnel or damage to machine may result.  Be sure to read and
understand the material presented in this User’s Guide and in any other
accompanying instructions.

The purpose of this manual is to supplement, but not to replace the services of
qualified personnel to start up and adjust this equipment.

Persons without previous experience with this equipment should not attempt the
initial adjustment and check out procedures required until this installation is
considered ready for operation by a qualified operator.

Each cabinet carries an individual serial number on the nameplate mounted on the
cabinet.  Please refer to this number when ordering replacement parts or when
requesting any further information.

This pressure supply system is primarily designed for the burst testing of plastic
pipe.

Содержание 3100 Series
































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды