Sapphire Audio rage Скачать руководство пользователя

Страница: 42 / 73

SECTION 4

PART#

49-057 REV K

SAPPHIRE SCIENTIFIC RAGE

TROUBLESHOOTING:

BLOWER / VACUUM PUMP

PROBLEM

CAUSE

SOLUTION

Loss of vacuum:

While

cleaning, the vacuum is not up

to specification. Engine RPM is

normal.

Vacuum gauge is giving an
improper reading.

Examine the tubing between the
vacuum relief valve and the vacuum
gauge and remove any blockage.

Vacuum hose(s) is damaged,
causing a suction leak.

Inspect hose(s), repair or replace.

Waste tank gaskets not sealing
properly, not positioned
properly

Inspect the gasket. Repair seal or
replace Re-position lid(s).

Plugged vacuum hose or
vacuum plumbing between
vacuum inlet and strainer
basket.

Unplug vacuum hose or inlet
plumbing.

Waste tank filter or strainer
basket is plugged.

Clean or replace filter. Clean strainer
basket.

Loose vacuum pump drive
belts.

Tighten the drive belts

Waste tank drain valve is
damaged or left open, causing a
vacuum leak.

Drain the waste tank. Close drain
valve, if open. Remove the dump valve
and, after inspecting, replace the
defective components.

Vacuum relief valve requires
adjustment or has a vacuum
leak due to damaged diaphragm.

Re-adjust the vacuum relief valve. If
the vacuum does not increase, remove
and inspect the relief valve diaphragm.
If damaged, replace

Vacuum pump is worn out.

Replace the vacuum pump.

TROUBLESHOOTING:
WATER PUMP

PROBLEM

CAUSE

SOLUTION

Loss of solution volume at

cleaning tool orifice:

Solution

pressure gauge reads normal.

Plugged orifice and/or screen in
the cleaning tool.

Unplug or replace orifice and/or screen

Internal block between the
pressure regulator manifold and
the outlet manifold, or the
solution screen is clogged

Inspect all lines, remove accumulated
debris which is blocking proper flow.
Replace any defective hoses. Remove,
inspect, and clean the solution screen.
De-scale unit and install a water
softener, if necessary.

Outlet check valve is plugged

Examine the check valve, remove any
debris

Cleaning tool valve is
malfunctioning.

Repair or replace valve.

Содержание rage










































































Результаты поиска

Содержание rage

Отзывы:

Похожие инструкции для rage

Бренды по названию

Популярные бренды

Sapphire Audio rage, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание rage

Отзывы:

Похожие инструкции для rage

Бренды по названию

Популярные бренды