Sanwa MT-R RX-493i, Руководство пользователя

Страница: 23 / 31

44 43
How to Use Each Feature
How to Use Each Feature
How to Use Each Feature
Back
Enter
▲
▼
Push
ENTER
Note
• BINDING is not done at the factory. Please make sure to complete BINDING before use.
• When the receiver is new, make sure to complete BINDING for the transmitter and the new receiver.
• Make sure to use the set of the transmitter and the receiver that completed BINDING.
•
•
When changing the setting in the BIND menu after BINDING, repeat BINDING.
When changing the setting of the mode (NOR/SHR/SSR/SUR) after BINDING, repeat BINDING. If you do not re-BIND, setting changes will
not be reflected.
Note) Though the wire is not connected
to the above-mentioned receiver,
keep the servo and FET speed
controller (excluding motor),
battery in connected state.
BIND plug
Connect BIND
plug to receiver
Switch ON
Switch ON the power
supply of receiver/
FET speed controller.
ENTER
Flashing
ENTER
・・・・・・・・・・・・・・・・・・ ・・・・・・・・・・・・・・・・・ ・・・・・
BIND Plug
Finished Bind Mode
on the transmitter
Take off Bind Plug from the receiver
Status of the Receiver LED
(Flashing with approximately 0.5-second interval)
(High-speed flashing)
BINDING Complete (Light on)
Note that, in SHR/SSR/SUR mode, an analog servo will not work. If you mistakenly use an analog servo in
SHR/SSR/SUR mode, it will not operate normally and the servo will be broken.
Do not use an analog servo in SHR/SSR/SUR mode.
For digital servo (SRG, ERB ERS series, Digital ERG series), it can work for either mode of NOR/SHR.
SSR mode works only for PGS ,SRG servo, SUPER VORTEX series, HV-12 STOCK SPECIAL and HV-01.
SUR mode works for only PGS servo, SUPER VORTEX Gen2 / PRO / SV-D2.
In SHR/SSR mode, BL/RACER, BL/FORCE, F2000, F2200, F3000, F3300, SBL-01, 02 and 03CL do not work.
BL-SIGMA, SV-08, HV-10, HV-12 and F2500 work in NOR/SHR mode.
•
•
•
•
IMPORTANT
•
Output System
Response Mode
ENTER BACK
ENTER BACK
SYSTEM MENU
SYSTEM
BIND
● Select the output system that suits the receiver, set a mode for the servo (analog/digital) and the speed
controller to be used and bind the transmitter with the receiver.
When using first time, please bind with receiver.
*MT-R does not bind with RX-493i of the factory.
1) Select [SYSTEM] with the up and down key.
Determine with the Enter operation.
2) Select [BIND] with up and down.
Determine with the Enter operation.
3) Setting RF MODE (Signal output system)
○ Output System
・ FH5
RX-491,RX-492, RX-493, RX-493i
*FH4, FH3, FH-E, DS mode receivers are not compatible.
4)Setting Channel Mode
Set the response mode for each channel with up and down key.
・ You can the set the response mode for each channel.
○ Setting Range: NOR(Normal)
SHR(High Response)
SSR(Super Response)
SUR (Ultra Response)
○ Default: NOR
● A feature for setting system of the transmitter, such as Bind, Key Assignments (KEY ASSIGN),Buzzer,
Battery, LCD and CALIBRATION.
7) Setting BIND
● What is BIND: Each of MT-R transmitters has its own unique ID (solid identification) number. BIND is to
let the receiver memorize the ID number. Operation will be possible only between the transmitter and the
receiver that completed Binding.
1] When setting in the BIND menu is done, set BIND
with up, down, and enter key.
2] Move the cursor to [ENTER] in the BIND menu and operate Enter.
The transmitter now is ready for BIND operation.
3] Turn on the receiver with inserting Bind Plug in BIND/SSL port.
4] When BINDING is done properly, the LED of the receiver starts
flashing slowly at first then it flashes in high speed.
When the LED of the receiver flashes in high speed,
operate the Enter key of the transmitter to complete
BINDING.
Then, please take off the Bind Plug from the receiver.
When BINDING is done properly, the LED of the receiver is lit.
When the LED of the receiver is lit, please check the bind completion
by using servo operation.
*When BINDING cannot be done properly, restart from step 2).