Sanwa MT-R RX-493i, Руководство пользователя

Страница: 18 / 31

34 33
How to Use Each Feature
How to Use Each Feature
How to Use Each Feature When Mode Setting Is CODE 10
*CODE6
～１０
is not displayed on top display.
Please check display on the AUX menu.
+100 -100
CODE1 Parameter
CODE2 Parameter
CODE3 Parameter
CODE4 Parameter
CODE5 Parameter
0
Switch Type
Mode Setting
Shortcut for Key Assign
Switch CH to SET with up and down key.
Select SET with enter.
AUX TYPE = When setting is CODE AUX, bar display
Servo Monitor
Mixing Rate Setting
Shortcut for Key Assign
Switch CH to SET with up and down key.
Select SET with enter.
AUX
AUX
AUX MIXING [AUX MIX]
CODE AUX
● AUX menu sets the performance of AUX1 and AUX2 (3ch, 4ch). You can choose from STEP AUX (STEP),
POINT AUX (POINT), 4WS (4-Wheel Steering: Coordinate Phase, Opposite Phase). MOA (Motor On
Axle), AUX-MIX (AUX Mixing: ST → AUX/TH-AUX) and CODE-AUX.
● Setting AUX Mixing allows you to mix from the steering to AUX and from the throttle to AUX.
1) Select [AUX] with enter.
2) Change [SET] menu with enter.
*Switch CH to SET with up and down key.
3) TYPE setting (AUX-MIX)
Select [AUX-MIX] on AUX TYPE setting with up and down key.
4) MODE Setting
Set mixing mode to the used method.
○ Setting Range: ST-mix / TH-mix
○ Default: ST-mix
*ST-mix is mixed from the steering to AUX.
TH-mix is mixed from the throttle to AUX.
5) Mixing rate setting
Set mixing rate with up and down key.
○
Setting Range: 0%
～
100%
○
Default: 100%
*Assign the features of the Mixing Rate to Trim or the switch
with Key Assignments, or operate with up and down key.
● Code AUX (CODE AUX) is a feature to perform code communication
by assigning a setting value to each code of CODE1-CODE10.
It is an extension feature to change the setting of speed controller (SUPER VORTEX series/ SV-D2), PGS
servo series, and the Gyro System (SGS-01C/SGS01D/SGS-02) that are compatible to CODE AUX.
● You can set 2 types of Code AUX1 and CODE AUX2.
*Please set response mode [SHR] on A1 and A2 when binding with a receiver. (p.43).
*In case of using CODE AUX, please do NOT conect servos on receiver CH3 and CH4 port.
1) Select [AUX] with up and down key.
2) Change [SET] setting menu with enter.
*Switch CH to SET with up and down key.
3) Type Setting (CODE AUX)
Select [CODE] on AUX TYPE setting with up and down key.
*CODE is only compatible with CODE10 products.
*MT-R is not compatible with CODE5 products such as
SV-ZERO, SV-SPORT, SV-TYPE D, SGS-01, and SGS-01D.
4) Mode setting
Display function name for CODE10 products
by setting mode for compatible product.
○ Setting Range: CODE/SV-G/D(only AUX1)
CODE/PGS/SGS-02 (only AUX2)
○ Default: CODE
5) CODE AUX setting
Select CODE with enter you want.
Set value with up and down key.
*In case of setting CODE on AUX TYPE, CODE AUX
setting condition will display on top screen as below pictures.