SANKI MFC-S3B Скачать руководство пользователя страница 31

Страница: 31 / 36

29 / 32

14.

Troubleshooting

Trouble

Probable cause

Corrective action

The feeder does not vibrate.

The power cable is not connected.

Connect the power cable.

“Voltage (%)” is “0.0.”

Set “Voltage(%).”

The set frequency is wrong.

Adjust the frequency to the
resonance frequency.

The output connectors is disconnected from
the feeder.

Connect the output connector to
the feeder.

The RUN lamp is OFF.

Check the external control and the
overflow sensor.
Check the parameter settings.

The RUN lamp is blinking.

Press the ON/OFF key

Voltage(%) cannot be set.

The AUTO lamp is ON. (The mode is the

“A” mode.)

Switch the mode to

the “n” mode.

The

frequency

cannot

adjusted.

The AUTO lamp is ON. (The mode is the

“A” mode.)

Switch the mode to the “n” mode.

The F-

LOCK lamp is ON in the “n” mode.

Release the lock.

When the power supply is turned
OFF, the voltage and frequency
settings disappear.

The data has not yet been saved.

Save the data.

The overcurrent error (E-01) is
displayed.

The feeder is probably abnormal.

Contact the dealer.

Ground fault was caused due to damage to
the controller output cable cover or the
feeder wire cover.

Replace the damaged cable or wire.

The frequency is deviant.

Adjust the frequency to the
resonance frequency.

One of the memory errors (E-10

–

12) occurs when the controller

starts.

There was a memory error when the power
supply was turned ON.

Reset the power supply.
If the same error recurs, contact
our sales agent for consultation.

15.

Options

Name

Applied wire

Length (mm)

Terminal

Remarks

Power cable (for 3A)

VCTF 0.75x3

1200

Nichifu pin terminal male

PC-2005M

Mounting as
standard

Power cable (for 6A)

VCTF 1.25x3

1200

Nichifu pin terminal male

PC-2005M

Output cable (for 3A)

VCTFK 0.75x2

1200

Molex terminal

1189ATL

Molex housing

1490R1

Output cable (for 6A)

VCTFK 1.25x2

1200

Molex terminal

1189ATL

Molex housing

1490R1

Overflow sensor
input cable (P3 cord)

VCTF 0.3x3

320

Molex terminal

1381ATL

Molex housing

1396R1

Vibration sensor
input cable (P4 cord)

MOGAMI 2330
(Low Noize Wire)

1200

Molex terminal

1189ATL

Molex housing

1545R1

Vibration sensor
(KS-3)

MOGAMI 2330
(Low Noize Wire)

1000

Molex terminal

1190TL

Accessory

Molex housing

1545P1

Vibration sensor
input extension cable

MOGAMI 2330
(Low Noize Wire)

2000

Molex terminal

1190TL/1189ATL

Molex housing

1545P1/1545R1

Содержание MFC-S3B





































Результаты поиска

Содержание MFC-S3B

Отзывы:

Похожие инструкции для MFC-S3B

Бренды по названию

Популярные бренды

SANKI MFC-S3B, Инструкция по эксплуатации

Результаты поиска

Содержание MFC-S3B

Отзывы:

Похожие инструкции для MFC-S3B

Бренды по названию

Популярные бренды