background image

12 / 32 

7.

 Operation Panel

 

7-1.

 

Explanation of Operation Panel

 

 

 

 

 

 

 

 

 

 

 

 

 

1)

 Pilot lamps

 

 
 

No 

Name 

Function 

 

Data display 

A 7-segment, 4-digit LED 
Displays voltage, frequency, each settings and error codes.

 

 

Frequency pilot lamp 

ON when the data display is showing frequency 

 

Voltage % pilot lamp 

ON when the data display is showing voltage 

 

Operation pilot lamp 

Indicates the output condition of the controller. 
ON: The Controller is in operation under external control. 
Blinking: The Controller is in forced operation by the ON/OFF key. 
Long OFF and blinking: The Controller is at a forced stop by the   

ON/OFF key.

 

 

Parameter mode pilot 
lamp 

ON: The parameter setting is in process. 
Blinking: The speed magnification change setting is in process (only 

for 0u:1 

in the “A” mode).

 

 

Operation mode pilot 
lamp 

ON: “A” mode (operation)

 

OFF: “n” mode (adjustment)

 

Blinking: The function setting selection is in process.

 

 

Constant-amplitude 
control pilot lamp 

ON: Constant-amplitude control (

for 0u:1 in the “A” mode

)

 

OFF: Constant-voltage control (for 0u:0 

in the “A” mode

 and the 

n

 mode)

 

 

Frequency lock pilot 
lamp 

ON: The frequency is locked. 
OFF: The frequency lock is released. 

 

Operation pattern 
setting pilot lamp 

ON: Panel setting (only for setting in the “n” mode)

 

OFF: External signal setting 
Blinking: The function setting selection is in process.

 

Содержание MFC-S3B





































Отзывы: