Sanden Vendo Vue SXY 30, Руководство пользователя

Страница: 121 / 128

T-7
Part #1167879 07/2008
ERROR
DESCRIPTION OF ERROR CODE
CHECKING METHOD
CORRECTIVE
ACTION
Hop.Buck No Current
Hopper Bucket motor either did not run, or no current was detected.
Check Hopper Bucket harness connection.
Plug in hopper bucket connector
. Run
T
est Hopper Bucket in
T
est
Mode.
Run
T
est Hopper Bucket in
T
est Mode
If motor moves, current detection circuitry has been damaged on VMC. Replace VMC board.
Hopper Flap Jam
VMC detected high current while running the Hopper Bucket.
Run
T
est Hopper Bucket in
T
est Mode
If motor does not move, replace Hopper Bucket motor
.
Check to see if product is jamming the Bucket
Remove the product. Run Hopper Bucket
T
est.
Hopper Flap Switch
Hopper
flap
motor
runs
but
does not detect the home switch.
Run
T
est Hopper Flap in
T
est Mode
Replace
hopper
flap
motor
assy
.
Hopper Bucket Switch
Hopper bucket motor runs but does not detect the home switch.
Run
T
est Hopper Bucket in
T
est Mode
Replace the hopper bucket motor assy
.
Selection Switches - Keypad
Stuck Selection SW on Keypad
Bad Selection Switch - Selection switch within the Keypad is actuated for more than 15 seconds while in the Customer Mode or Door Open Sales
T
est Mode.
Check the selection switch number shown in the detailed error code “nn” to see if: 1) if the Keypad is defective; 2) the harness is wired wrong/shorted
T
ry to correct the problem if one of the two items are found. If you can’t
correct it, then replace the component in question.
Coin Changer
Coin Communication
Changer communication error - no changer communication for more than 2 seconds.
Check
that
red
light
is
flashing
on
control
board.
If
light
is
not
flashing,
there
is
no
power
to
board.
Check
and
replug
any
unplugged connections.
Check fuse on the power distribution panel.
If fuse is blown replace it. Replace transformer
.
Defective acceptor
.
Replace acceptor
.
T
ube Sensor
T
ube sensor is defective
-- reported by changer
.
Check changer tubes for blockage
Clear tube blockage. If no blockage is found, replace changer
.
Coin Inlet
Changer inlet chute blocked - no coins sensed for over 96 hours by the changer
.
Check inlet chute for blockage. Drop coins in Sales Mode or
T
ube
Fill Mode to test acceptance. Manually clear the error
.
Clear inlet chute blockage. If no blockage found, replace changer
. If
acceptance rate is acceptable, system is OK. If acceptance rate is low or changer will not accept coins, replace changer
.
T
ube Jam
T
ube pay out jam -- reported
by changer
.
Check changer tubes and payout for blockage.
Clear blockage, if found. If no blockage is found, replace changer
.
Coin Read Only Memory
Changer check sum incorrect -- reported by changer
.
Unplug
machine,
wait
at
least
five
seconds,
replug
machine.
Manually clear the error
If error does not clear
, replace changer/acceptor
.
Replace acceptor
Excessive Escrow
Excessive escrow requests -- more than 255 requests since the last coin was sensed.
Check escrow lever and associated mechanisms.
Manually clear the lever and error
.
Close door then reopen. Check to see if error still occurs.
Replace changer/acceptor
.
Coin Jam
Coin jam - reported by changer
Check changer/acceptor for jammed coins or other obstructions.
If no obstructions are apparent, replace changer/acceptor
Low
Acceptance
Low
acceptance
rate
--
coin
acceptance has fallen below 80%
Check changer/acceptor for obstructions or dirt
If no obstructions are apparent, and acceptance appears to be OK, this may be an indication of cheating attempts.
Drop coins test acceptance.
If no obstructions are apparent and coins do not accept, or acceptance rate is poor
, replace changer/acceptor
.