background image

S&C Instruction Sheet 766-557    3

Understanding 

Safety-Alert Messages

There are several types of safety-alert messages which may appear throughout this 
instruction sheet as well as on labels attached to the 

IntelliRupter fault interrupter

Familiarize yourself with these types of messages and the importance of the various 
signal words, as explained below

.

Ç

 

DANGER

“DANGER” identifies the most serious and immediate hazards 

that will

 likely result in 

serious personal injury or death if instructions, including recommended precautions, 
are not followed .

Ç

 

WARNING

“WARNING” identifies hazards or unsafe practices that 

can

 result in serious personal 

injury or death if instructions, including recommended precautions, are not followed .

Ç

 

CAUTION

“CAUTION” identifies hazards or unsafe practices that 

can

 result in minor personal injury 

if instructions, including recommended precautions, are not followed .

NOTICE

NOTICE

” identifies important procedures or requirements that 

can

 result in product or 

property damage if instructions are not followed .

Following 

Safety Instructions

If you do not understand any portion of this instruction sheet and need assistance, 
contact your nearest S&C Sales Office or S&C Authorized Distributor. Their tele- 
phone numbers are listed on S&C’s website 

sandc.com

 Or call S&C Headquarters  

at (773) 338-1000; in Canada, call S&C Electric Canada Ltd. at (416) 249-9171.

NOTICE

Read this instruction sheet thoroughly and carefully 
before installing or operating your S&C IntelliRupter 
PulseCloser Fault Interrupter .

Replacement 

Instructions  

and Labels

If you need additional copies of this instruction sheet, contact your nearest S&C Sales 
Office, S&C Authorized Distributor, S&C Headquarters, or S&C Electric Canada Ltd.

It is important that any missing, damaged, or faded labels on the equipment be replaced 

immediately. Replacement labels are available by contacting your nearest S&C Sales 
Office, S&C Authorized Distributor, S&C Headquarters, or S&C Electric Canada Ltd.

Safety Information

Содержание IntelliRupter PulseCloser SDA-4650R2

























Отзывы: