Thank You!
for purchasing your new S&B Filters Helmet Particle Separator. If at any time you need additional assistance with installation or
have any other questions or comments, feel free to call our customer support team at 909-947-0015. You can also take advantage of our live chat
at www.sbfilters.com and connect with an S&B representative immediately. We hope you enjoy your new S&B Filters product and thank you for
your continued support.
THREAD LOCKER USE
We have provided a small tube of thread locker in your kit. Whenever
you see the symbol above on a step of the instructions apply 1 small
drop of the thread locker to the threads of the screws or bolts. This will
keep your hardware from vibrating loose during rough driving. If the
hardware ever needs to be removed, do so slowly to avoid having the
inserts strip out from the plastic.
• Please read the entire product guide before proceeding.
• Ensure all components listed on pages 3 are present.
• If you are missing any of the components, call the S&B
Customer Support Team at (909) 947-0015.
• Disconnect your battery before doing any electrical
modifications.
BEFORE YOU START
2
THIS EQUIPMENT SHOULD BE INSTALLED, ADJUSTED, AND SERVICED BY PERSONNEL FAMILIAR WITH THE CONSTRUCTION
AND OPERATION OF THIS TYPE OF EQUIPMENT AND THE HAZARDS INVOLVED. FAILURE TO OBSERVE THIS PRECAUTION COULD RESULT
IN SEVERE INJURY. READ THIS MANUAL THOROUGHLY AND MAKE SURE YOU UNDERSTAND THE PROCEDURES BEFORE YOU ATTEMPT
TO OPERATE THIS EQUIPMENT. THE PURPOSE OF THIS MANUAL IS TO PROVIDE YOU WITH INFORMATION NECESSARY TO SAFELY OPER-
ATE, MAINTAIN, AND TROUBLESHOOT THIS EQUIPMENT. DO NOT USE THIS EQUIPMENT FOR ANY REASON OTHER THAN ITS INTENDED
PURPOSE. FAILURE TO FOLLOW THESE INSTRUCTIONS WILL VOID ANY WARRANTY. KEEP THIS MANUAL FOR FUTURE REFERENCE. THE
INFORMATION CONTAINED IN THIS MANUAL IS SUBJECT TO CHANGE WITHOUT NOTICE.
Product will intake and expel both air and loose materials with high force and velocity.
• Install product by affixing to the rear upper or rear lower roll bar and ensure the air inlet is not blocked.
• If using product with only one rider, place provided rubber cap over helmet air output port not in use. Failure to do so may result in
low pressure and low flow to the port that is in use. It will also lead to possible contamination of the clean air chamber resulting in a
greater chance of debris entering the connected helmet.
• Do not place face, hair, extremities, clothing, or other loose material in front of air inlet or outlet during use.
• Install product by affixing to the rear upper or rear lower roll bar to avoid placing hair, extremities, clothing, or other loose material in
front of air inlet during use.
Moving parts are sharp and could cause personal injury.
• Keep fan safety cages, blower outlet, and exhaust cover in place while operating and after service.
• Disconnect product from power source before servicing.
Product is designed to filter approximately 99% of solid particulate, such as dirt and dust. No filtration device is 100% effective, and
users may still experience distribution of dirt/dust within their helmet. To minimize this experience, ensure connection of the product to
user helmet at either of three locations. Directly on the helmet at the top right, top left, or top center ports. Connection of the product
to another location on the user helmet may increase the risk of use inhalation or eye exposure to dirt, dust, or other solid particulate
matter.
Product is designed for use in conjunction with an ATV’s operating manual, and state and federal law.
• Keep your seat belt fastened and wear a helmet while operating the vehicle.
Risk of electric shock!
• Improper installation, maintenance or operation could cause serious injury or property damage.
Periodically check the following:
• the Helmet PS exhaust fan and blower fan making sure they are working properly and blowing out air like when it was new.
• the fasteners of the Helmet PS assembly making sure they are tight and secured.
• the mounting brackets, straps and fasteners making sure they are tight and secured.
• the wire harness for any signs of wear making sure it is secured and away from any hot or moving components.
Important safety information and/or operating instructions for the end user might be included in this installation instruction sheet.
Make sure to give the instruction sheet included with this kit to the customer. Verify that the customer has access to all the information
required for proper use of the Helmet PS.
WARNING:
Содержание 76-6000
Страница 4: ...EXPLODED VIEW 3...
