Samsung ProXpress M4030 Series Скачать руководство пользователя

Страница: 150 / 178

4. Troubleshooting

4.7.2.8. U2-xxxx type (LSU) error code

► Error Code

U2–1111 / U2-1112 / U2–1113

► Error message

Error: #U2-111x / LSU Failure: #U2-111x.Turn off then on. Call for service if the problem persists

► Symptom

LSU Motor does not work normally.

► Troubleshooting method

1) Execute the LSU motor test in SVC mode. Check LSU motor operation sound.

2) If there is no sound, remove the right cover. Check if the LSU harness is connected on the main board properly.

3) If it is OK, remove the top cover. Check if the LSU harness is connected on LSU board properly.

4) Check if the LSU harness is defective.

5) Reconnect the LSU harness and then execute the LSU motor test again.

6) If the problem persists, replace the LSU.

7) If the problem persists after replacing LSU, replace the main board.

4-68

Содержание ProXpress M4030 Series














































































































































































Результаты поиска

Содержание ProXpress M4030 Series

Отзывы:

Похожие инструкции для ProXpress M4030 Series

Бренды по названию

Популярные бренды

Samsung ProXpress M4030 Series, Руководство по обслуживанию

Результаты поиска

Содержание ProXpress M4030 Series

Отзывы:

Похожие инструкции для ProXpress M4030 Series

Бренды по названию

Популярные бренды