Samsung ProXpress M4030 Series Скачать руководство пользователя

Страница: 120 / 178

4. Troubleshooting

4.7.2.2. Ax-xxxx (Motor_Fan_Sensor error)

► Error Code

A1–1112

A1–1113

► Error message

Error: #A1-1112 / Motor Failure: #A1-1112. Turn off then on. Call for service if the problem persists

Error: #A1-1113 / Motor Failure: #A1-1113. Turn off then on. Call for service if the problem persists

► Symptom

Main (OPC) motor operation is abnormal.

► Troubleshooting method

•

A1–1112 : Main motor is not operated for print-job.

•

A1–1113 : Main motor is operating but machine recognizes status as "Stopped".

1) Turn the machine off then on. If the error persists, check the following.

2) Remove the side cover.

3) Check the connection between the main motor and main board.

4) If the connection is OK, enter SVC mode. Execute the motor test.

(Diagnostics > Engine Diagnostics > Engine Test Routines)

a) If the motor is not operational,

i) Check the motor signal(3.3V). If the signal is abnormal, replace the main board.

ii) Check the power(24V). If the power is abnormal, check the SMPS board. If the SMPS board is defective,

replace it.

iii) If the motor signal and power is normal, replace the main motor or main drive unit.

b) If the motor is operational, replace the main board.

4-38

Содержание ProXpress M4030 Series














































































































































































Результаты поиска

Содержание ProXpress M4030 Series

Отзывы:

Похожие инструкции для ProXpress M4030 Series

Бренды по названию

Популярные бренды

Samsung ProXpress M4030 Series, Руководство по обслуживанию

Результаты поиска

Содержание ProXpress M4030 Series

Отзывы:

Похожие инструкции для ProXpress M4030 Series

Бренды по названию

Популярные бренды