Samsung OFFICESERV 500 Series Скачать руководство пользователя страница 21 | Manualshive

Страница: 21 / 113

background image

OfficeServ 500 Wireless LAN Service Manual/Ed.00

CHAPTER 3. Installation

© SAMSUNG Electronics Co., Ltd.

Page 1-5

Also, if the 10 M/100 Mbps LAN port, which is provided by the OfficeServ 500

System, is used, the application program like the PCMMC(PC for programming)
uses can be used while connected to Ethernet.
The OfficeServ 500

System supports the Q-Sig networking function that performs

call transfer, DND(Do Not Disturb), CCBS(Call Completion to Busy Subscriber),
and CCNR(Call Completion on No Reply) between the OfficeServ 500

systems,

regardless of the physical location of the system.
Since both hardware and software in the OfficeServ 500

System are designed with

module-based method, upon the need of users, the main line or subscriber’s line can
be easily scaled up or a new software can be installed to add new functions even
during the operation.
Connecting various terminals and additional equipment, the OfficeServ 500

System

can make an integrated environment that provides effective and various services for
wireless LAN users to keep pace with the high speed network and digitalized office
environment.

3.1.2 Major

Functions

The major functions of OfficeServ 500

System are described as follows :

Application of New Technology

The OfficeServ 500

System uses the following new technologies to upgrade the

digital exchange system.

Support for VoIP (Voice over Internet Protocol)

10M/100Mbps LAN Port is provided.

Q-Sig networking is supported.

Various kinds of highly integrated card(ITM3, MGI1/2, and TEPRI card)

Powerful system diagnostic/management program is provided.

New key set(DS Series, IP Phone, and Wide LCD) is supported.

The functions of wireless voice and data using the wireless LAN are provided.

Compatibility with the existing system

At the cabinet of OfficeServ 500

System, most cards of existing SKP-180D phone

system can be mounted as they are. Also, the existing terminal can be connected.
Therefore, the cost saving will be great when expanding the capacity and
performance of existing phone system.

Ease of System Installation

Since the OfficeServ 500

System is designed with module-based method, hardware

or software, such as card or cabinet, can be easily added. To the universal slot of
cabinet, any cards can be mounted, such as the main card or extension card, the ISDN
card and other cards providing premium services.

«
...
19
20
21
22
23
...
»

Содержание OFFICESERV 500 Series


















































































































Отзывы:

Нет отзывов

Похожие инструкции для OFFICESERV 500 Series

Бренд: Panasonic Страницы: 2

Бренд: Panasonic Страницы: 6

Бренд: Panasonic Страницы: 142

Бренд: Panasonic Страницы: 68

Бренд: Panasonic Страницы: 68

Бренд: Accutrol Страницы: 25

ProducTVity Station

Бренд: red lion Страницы: 8

Бренд: Quickie Страницы: 108

Бренд: Skytec Страницы: 12

Бренд: B&B Molders Страницы: 18

Бренд: Fancom Страницы: 51

Бренд: Bose Страницы: 2

Бренд: Greenheck Страницы: 16

Бренд: Gamma Vacuum Страницы: 43

Passport Event Series 2

Бренд: Fender Страницы: 44

DELTABOX BASS GENERATOR

Бренд: Vibe Страницы: 12

Бренд: Exibel Страницы: 64

Бренд: quiko Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды