Samsung NP-M70 Скачать руководство пользователя страница 140 | Manualshive

Страница: 140 / 195

Samsung NP-M70 Скачать руководство пользователя страница 140

System Management 121

You can also reserve Turning Computer Off, Hibernation state, Hold Mode,
etc. by selecting

System > Computer Scheduling

in the EasyBox program.

(see “Using EasyBox” on page 40.)

If you change the power settings in the Battery Manager program, the settings
of the '

Power Options Properties

' window are automatically changed

accordingly ('Using the Battery Manager' (p127)).

Hibernate Mode

(

Power Management or Manual Method

)

When hibernation is used, your computer turns off and when you power up again,
everything is restored exactly as you left it—including programs and documents
you may not have saved or closed. Everything in memory gets saved to the HDD,
and the monitor and hard disk get turned off.

If You Reinstall Windows:

You should re-establish hibernate in power options by opening

Power

Options Properties

window and click on the

Hibernate

tab then click

“Enable Hibernation”.

Frequent Interruptions:

If you experience frequent interruptions, you might also consider putting your
computer into automatic hibernation after a specified number of minutes using
the power management options.

Hibernate Tab

«
...
138
139
140
141
142
...
»

Содержание NP-M70




































































































































































































Отзывы:

Нет отзывов