Samsung AG AN4DKH Series Скачать руководство пользователя страница 17

17

Installation Pr

oc

edur

e

English

Individual drainage

Use a leveler to check that the fan coil unit is parallel to the ceiling.

If the slope of the drain pipe is less than 1/100, be sure to install an air vent at the inlet of each drain hole to 

smooth the flow of condensation water.

If the drain pipe is installed higher than the connection port, install the drain pipe vertically within a distance of 

300 mm from the flexible hose connection port. (Slim 1 way cassette)
•  However, because the water may leak, the height of the drain pipe should not exceed 550 mm.

Install the drain pipe at a slope of 1/100 or more.

Make sure that the distance between the supports is 1 to 1.5 m.

In order to prevent odor from the outlet of the drain pipe, install a trap at the end of the drain pipe or install an 

indirect drain.

Do not apply force to the hose when connecting the drain pipe.
•  Make sure that the hose connection is not loosened and as close as possible to the wall or other support, as 

shown in the figure.

 

 

 

 

• If the slope of the drain pipe is insufficient (less than 1/100), be sure to 

install an air vent at the top of each fan coil unit to prevent water from 

flowing back to the unit.

200 mm or less

100 mm 

or more

1 to 1.5 m

100 mm or less

(200 mm or less)

• Fix one of the flexible hoses to the  

ceiling using a hanger so that the 

straight section is maintained.

• Be sure to insulate the flexible hose, 

and then fix it with a clamp. (To 

prevent damage to the flexible hose)

Clamp

Straight section

Horizontal drain pipe  

(transverse pipe)

Ceiling

※  Install the horizontal drain pipe (transverse pipe) lower than the flexible hose.

More than 1/100 slope

Full thread  

bolt hanger

600 mm

or less

Flexible hose

Air vent

•  Do not install the flexible hose so 

that it is bent within 90 degrees, 

as shown in the figure. (The bent 

drain hose may degrade drainage 

performance.)

•   Do not install the flexible hose in a 

loop shape, as shown in the figure. 

The air in the pipe is not smoothly 

drawn out, causing air pockets and 

backward flowing of drainage.

DB68-11289A-01_IM_DVM FCU WindFree 4way_EU_EN_.indb   17

2022-04-26   오전 8:55:19

Содержание AG AN4DKH Series













































Отзывы: