manualshive.com logo in svg

Samson Media 7, Монтаж и эксплуатация

Поделиться
Скачать
Samson Media 7 Скачать руководство пользователя страница 6

6  

EB 9510 EN

Safety instructions and measures

Explosion-protected versions of this device must be operated only by personnel who has un

-

dergone special training or instructions or who is authorized to work on explosion-protected 
devices in hazardous areas.

Personal protective equipment

We recommend wearing the following protective equipment depending on the process medi

-

um:

 

−

Protective clothing, gloves, eye protection and respiratory protection in applications with 

hot, cold and/or corrosive media

 

Î

Check with the plant operator for details on further protective equipment.

Revisions and other modifications

Revisions, conversions or other modifications of the product are not authorized by SAMSON. 
They are performed at the user's own risk and may lead to safety hazards, for example. Fur

-

thermore, the product may no longer meet the requirements for its intended use. Use of the 
device is no longer permitted.

Warning against residual hazards

To avoid personal injury or property damage, operators and operating personnel must pre-

vent hazards that could be caused in the device by the process medium and operating pres

-

sure by taking appropriate precautions. They must observe all hazard statements, warning 

and caution notes in these mounting and operating instructions, especially for installation, 
start-up and service work.

Responsibilities of the operator

The operator is responsible for proper operation and compliance with the safety regulations. 
Operators are obliged to provide these mounting and operating instructions to the operating 
personnel and to instruct them in proper operation. Furthermore, the operator must ensure 

that operating personnel or third persons are not exposed to any danger.

Responsibilities of operating personnel

Operating personnel must read and understand these mounting and operating instructions as 

well as the specified hazard statements, warning and caution notes. Furthermore, the operat

-

ing personnel must be familiar with the applicable health, safety and accident prevention 
regulations and comply with them.

Содержание Media 7

































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды