Samson 2357-3 Скачать руководство пользователя страница 32 | Manualshive

Страница: 32 / 40

Samson 2357-3 Скачать руководство пользователя страница 32

32

EB 2559 EN

Malfunctions

Table 4:

Troubleshooting

Malfunction

Possible reasons

Recommended action

Tank pressure

drops below

the adjusted

set point

Operating bellows blocked by

the formation of ice

Î

Use a heat gun to melt ice.

DANGER

!

Depending on the process medium:

−

Potentially explosive medium

−

Potentially explosive atmosphere

Pressure build-up vaporizer iced

up

Î

Reduce consumption until most ice has melted.

Formation of ice on the pressure

build-up vaporizer caused by

peak consumption

Î

Brush accumulation of ice off the regulator.

DANGER

!

Risk of burn injury from touching cold surfaces (see section 1.2)

Tank pressure

exceeds the

adjusted set

point

Frozen process medium is

blocking the plug.

Î

Install a new regulator or isolate the regulator and leave it

warm up. Afterwards check whether the frozen medium has

sublimated (e.g. dry ice)

No medium consumption (oper

-

ational standstill). Incoming heat

and medium vaporization.

Î

Ensure for continuous medium withdrawal

Safety function responds after

the tank has been filled.

Î

Close the shut-off valves (6.1 and 6.2) to isolate the regulator

and pressure build-up vaporizer. Reduce the tank pressure

through medium withdrawal or blow-off. After the pressure set

point in the tank is reached, reopen the shut-off valves.

8

Malfunctions

The malfunctions listed in Table 4 are caused
by mechanical faults and incorrect regulator
sizing. In the simplest case, the functioning
can be restored following the recommended
action. Special tools may be required for re

-

pair work.
Exceptional operating and installation condi

-

tions may lead to changed situations that
may affect the control response and lead to
malfunctions. For troubleshooting, the condi

-

tions, such as installation, process medium,
temperature and pressure conditions, must
be taken into account.

SAMSON's After-sales Service can help
during troubleshooting. Further information
is available in section 10.1. We recommend
removing the regulator from the pipeline be

-

fore repairing it.

SAMSON's After-sales Service can support
you in drawing up an inspection and test
plan for your plant.

Contact SAMSON's After-sales Service for
malfunctions not listed in the table.

Tip

Note

«
...
30
31
32
33
34
...
»

Содержание 2357-3









































Отзывы:

Нет отзывов