SAMLEX AMERICA INC. | 39
Setting Menu Screens
The “Setting Menu” is used to program various modes of operation and
important operational parameters.
The “Set Key” is used to first open the “Setting Menu” and then to scroll
the “Setting Menu” screens in the forward direction only. The “Setting
Menu” consists of 8 screens as shown below. The 8 “Setting Menu”
screens can be scrolled one by one in the forward direction only in the
form of a loop. For example, Screen 1
2
3
4…
8
1
2 …
Please note that it is not possible to go to the
previous screen of the “Setting Menu” by using the “Up” or “Down”
Keys. In case a previous “Setting Menu” screen is required, it will be
necessary to press the “Set Key” a number of times to scroll forward in
the loop to get to the required screen.
• Press for > 3 sec for opening the “Setting Menu”. The “Setting
Menu” starts with the first screen, Screen 1 as shown below. The
Green Status LED and the Red Fault LED will start blinking to indicate
that the unit is in the Setting Mode
• Once the “Setting Menu” is opened, press Set Key once to scroll to
the next “Setting Menu” screen.
• A short beep will be heard every time the Set Key it is pressed
• The programmable modes / values within the available range can be
chosen using the “Up” and “Down” Keys.
• Once the required value / mode is displayed, press the “Enter” Key
to accept the value / mode. As soon as the “Enter” Key is pressed,
the selected value / mode is entered in the memory and the “Setting
Menu” is automatically closed and exited. Please note that if any
correction is required to be made after pressing the “Enter” Key, the
“Setting Menu” will have to be opened once again as explained above
•
Please note that once the “Setting Menu” is opened, only
one parameter / mode can be programmed at one time. As
soon as the “Enter” Key is pressed after selecting the required
parameter / mode, the selected value / mode is entered in the
memory and the “Setting Menu” is closed and exited. The
“Setting Menu” will have to be opened once again to program
another parameter / mode.
SCReen 1
Generator Mode = enable / Disable (Default = Disable)
NOTE: Generator Mode in the Disabled condition will be displayed
as “Utility Mode” in normal display
G
e n
e
r
a
t
o
r
M o
d
e
D
i
s
a
b
l
e
oR
G
e n
e
r
a
t
o
r
M o
d
e
E
n
a
b
l
e
SCReen 2
Low Voltage Transfer =
80 ~ 95 VAC (Default = 85 VAC) - in steps of 1V
L
o
w
v
o
l
t
a
g
e
T
r
a
n
s
f
e
r
x
x
x
v
a
c
SCReen 3
High Voltage Transfer =
130 ~ 140 VAC (Default = 132 VAC) - in steps of 1V
H
i
g
h
v
o
l
t
a
g
e
T
r
a
n
s
f
e
r
x
x
x
v
a
c
SCReen 4
battery boost (Absorption) Voltage =
12V battery: 14 ~ 16V (0.1V Steps); Default: 14V
24V battery: 28 ~ 32V (0.2V Steps); Default: 28V
B
a
t
t
e
r
y
B
o
o
s
t
v
o
l
t
a
g
e
x
x
.
x
v
d
c
SCReen 5
battery Float Voltage
12V battery: 13 ~ 15V (0.1V Steps); Deafulat: 13.8V
24V battery: 26 ~ 30V (0.2V Steps); Default: 27.6V
B
a
t
t
e
r
y
F
l
o
a
t
v
o
l
t
a
g
e
x
x
.
x
v
d
c
SCReen 6
bulk Charging Current =
10 ~ 80A, each step 10A (Default = 10A) for G4-2012
bulk Charging Current =
10 ~ 70A, each step 10A (Default = 10A) for G4-2524 and G4-3524
C
h
a
r
g
i
n
g
C
u
r
r
e
n
t
x
x
A
SCReen 7
battery temperature compensation =
- 3.0 ~ -5.0mV /
°
C / Cell (Default = - 4.0 mV /
°
C / cell)
B
a
t
.
t
e
m p
.
c
o
m p
.
-
4
.
0
m v
/ c
e
l
l
SECTION 7 |
Setting Menu and
display Screens
