Operating instructions Hold-o-mat®
Seite 20
Operating instructions Hold-o-mat®
Seite 21
Operating instructions Hold-o-mat®
page 21
Operating instructions Hold-o-mat®
page 20
Buzzer volume: 3
"Hold" and "Hold with core temperature information" functions: 68°C
Programme 1 :
(e.g. roast beef, low temperature)
Phase 1 : 10 min. / 110°C
Phase 2 : 50°C KTM / 80°C
Phase 3 : 53°C KTM / 65°C
Programme 2 :
(e.g. roast beef overnight "American method")
Phase 1 : 10 min. / 110°C
Phase 2 : 53°C KTM / 65°C
Programme 3 :
(e.g. meat / sauce dishes overnight)
Phase 1 : 10:00 hours / 80°C (put in when hot)
Programme 4 :
(e.g. low temperature cooking of roast beef without "Cook" phase)
Phase 2 : 50°C KTM / 80°C
Phase 3 : 53°C KTM / 65°C
Programme 5 :
(e.g. à la carte Hold with core temperature and warning horn)
Phase 3 : 53°C KTM / 65°C
Freely programmable, including phase removal, average values for quick
data entry
Programme 6 :
Phase 1 : 10 min. / 110°C
Phase 2 : 50°C KTM / 80°C
Phase 3 : 55°C KTM / 68°C
Programme 7 :
Phase 1 : 10 min. / 110°C
Phase 2 : 50°C KTM / 80°C
Phase 3 : 55°C KTM / 68°C
Programme 8 :
Phase 1 : 10 min. / 110°C
Phase 2 : 50°C KTM / 80°C
Phase 3 : 55°C KTM / 68°C
Programme 9 :
Phase 1 : 10 min. / 110°C
Phase 2 : 50°C KTM / 80°C
Phase 3 : 55°C KTM / 68°C
Programme 10:
Phase 1 : 10 min. / 110°C
Phase 2 : 50°C KTM / 80°C
Phase 3 : 55°C KTM / 68°C
After phase 3, you are back to the programme number.
Either start the device now (button 7), change the programme again
(button 6) or switch the device off (button 1), so that the next day your
colleague can start the prepared programme.
Programmes remain stored even if there is a fairly long power cut.
If you press buttons 2 and 3 (Down and Up) simultaneously, the device
gives you a reference value (default value), so that you do not have to
begin each entry at zero. The exact default values are shown below.
Programmes 1 to 5 are programmes which can be changed immediately,
and give you the phase with which you want to work.
Programmes 6 to 10 are free programmes, which you can assign as you
wish. If you want to remove a phase, just go to a temperature value
below 20° in the appropriate phase, and the phase is removed (in both
displays, "- - -" appears).
In the case of programmes 6 to 10, to prevent an unintended program-
me change being made on viewing, before the change a release must
take place by the two buttons 2 and 3 (Down and Up) being pressed
simultaneously.
When a programme has ended, the buzzer sounds for one minute and
then stops. The Hold-o-mat remains in the "hold position" in the last pha-
se. If the core temperature overshoots, this is displayed from 1 degree
higher, and the display with the core temperature begins to flash.
�
!
�
!
�
!
Free programming
Optional programmes
End of programme
Default values
"Cook & Hold" function
"Hold-o-mat with KTM"