Salter Brecknell S122 Скачать руководство пользователя страница 7 | Manualshive

Страница: 7 / 63

Salter Brecknell S122 Скачать руководство пользователя страница 7

1.1 Electrical installation

1 Warnings

7

S122

User /

Service Instructions

1

Warnings

1.1

Electrical installation

The

power cord

must be connected to a supply outlet with a

protective earth

ground

. The electrical supply at the socket

outlet must provide over current protection of an appropriate
rating.

Pluggable equipment must be installed near an easily
accessible socket outlet. Permanently connected equipment
must have a readily accessible disconnect device
incorporated in the fixed wiring.

For your protection all (110V or 230V) equipment used
out of doors or in wet or damp conditions should be supplied
from a correctly fused source and protected by an approved
RCD to BS7071 or BS7288 or BS4293. IF IN DOUBT SEEK
ADVICE FROM A QUALIFIED ELECTRICIAN.

1.2

Risk of electric shock

This equipment is powered by

AC

voltage which presents

an electric shock hazard.

Always completely disconnect the power supply:

●

Before removing the

scale

covers

●

Before performing any routine maintenance

●

Before cleaning the

scale

1.3

Additional service precautions

●

When the covers are removed, do not apply power to the
unit unless specifically instructed to do in this handbook.

●

When working on live equipment, exercise great care,
use insulated tools and test equipment, and do not work
alone.

«
...
5
6
7
8
9
...
»

Содержание S122
































































Отзывы:

Нет отзывов