DEUTSCH
VERWENDEN SIE ANTISTATISCHE SCHLÄUCHE DER MARKE SAGOLA,
UM MÖGLICHE ELEKTRISCHE ENTLADUNGEN ZU VERHINDERN, DIE
BRÄNDE ODER EXPLOSIONEN VERURSACHEN KÖNNEN.
Verbinden Sie das Gerät und alle Elemente des Arbeitsprozesses immer mit einer
Erdung
, um statische Elektrizität zu vermeiden. Überprüfen Sie in regelmäßigen
Abständen (einmal pro Woche) die elektrische Durchgängigkeit. Wenn Ihr Widerstand
die empfohlenen Grenzwerte überschreitet, korrigieren Sie ihn. Nicht geerdete Geräte
können die Installation gefährlich machen
Gesamtableitungswiderstand <1 Million Ohm (Ω).
Lesen Sie aufmerksam alle Daten, Anweisungen und Sicherheitsmaßnahmen des Herstellers der
von Ihnen verwendeten Produkte durch und befolgen Sie diese (Spritzmaterial, Verdünnungsmittel,
usw.), da diese chemische Reaktionen, Brände und/oder Explosionen auslösen können oder es
sich bei diesen um Gift-, Reizstoffe oder schädliche Stoffe handeln kann, die in jedem Falle die
Gesundheit und Unversehrtheit des Benutzers und der Personen in dessen Umkreis gefährden
(siehe Abschnitt Gesundheit und Sicherheit).
Beim Mischen, Vorbereiten und Filtern des Produktes, das verwendet
werden soll, sicherstellen, dass den Anweisungen des Herstellers Folge
geleistet wird und dass kein Fremdkörper Bei Zweifeln hinsichtlich der
Reinheit des Produktes, dessen Zusammensetzung usw., setzen Sie sich
mit Ihrem Lieferanten in Verbindung.
Viskosität des Produktes, das angewendet werden soll, mithilfe des
Viskosimeter-Sets von SAGOLA, Bestellnummer - 56418001, überprüfen.
Der perfekte Verschluß des Deckels und Behälters
muß überprüft werden, wobei die Kontaktflächen
(Behälter und Deckel) produktfrei gehalten werden
sollten.
Es sollte vermieden werden den mit Produkt gefüllten
Kessel zu bewegen oder umzukippen.
Zwischen dem Produkt und dem Deckel einen
Mindestabstand von 10 cm freilassen.
VORSICHTSMASSNAHMEN HINSICHTLICH EXPLOSIONEN!
Vergewissern Sie sich, den Drucktank bei einem Lackdruck unter dem
maximalen Betriebsdruck zuverwenden. Die Verwendung bei einem
Lackdruck über dem maximalen Betriebsdruck könnte zur Explosion
des Materialdruckbehälter mit daraus folgenden schwerwiegenden
Gefahren führen. Die Leitungen fest anschließen, um Austreten
von Lack oder Abtrennen zu vermeiden. Sollte sich während der
Lackiervorgänge eine Leitung lösen, könnten die Bewegung des
Schlauchs und das Ausstoßen des Lacks zu schweren Verletzungen
am Körper führen.
Wenn das Gerät längere Zeit nicht benutzt werden soll, trennen Sie es von der Luftversorgung.
60/61
Ford Nº4
mín.
10 cm.
Содержание PREMIUM 30
