10
Too much grass waste in
the housing.
Clean the cutting chamber of
grass, ensure that the gap
between fan and housing is
kept clean (pull the plug
first!).
Get it checked by an
authorised workshop.
Extreme vibration
Have it checked by an
authorized dealer
Mower does not work
Pull drive control bar not
pulled.
Pull drive control bar
G
.
Have it checked by an
authorised workshop.
Drive speed cannot be
regulated
Have it checked by an
authorized dealer
Cut not clean,
lawn turns yellow
Cutting blade blunt.
Have it sharpened and
balanced by an authorised
workshop
Q
.
Cutting height too low.
Set higher cutting height
I
.
Mowing speed too high.
Adapt mowing speed, switch
motor drive off if necessary.
Insufficient overlap
between mowing lanes.
If grass is long, the mowing
lanes may need to overlap
further.
Lawn matted.
A perceptible improvement
can be achieved by using a
scarifier.
Ejector blocked
Turbo signal ignored
J
+
K
.
Empty the collecting bag
L
.
Cutting height too low
with grass too high.
Set higher cutting height
I
.
Mowing speed too high.
Adapt mowing speed, switch
motor drive off if necessary.
Grass is damp.
Allow the lawn to dry.
The mulched grass
does not look good:
clumps, excessive cut
material, coarse cut
Cutting blade blunt.
Have it sharpened and
balanced by an authorised
workshop
.
Mulching rule ignored
(cut max. 1/3 of grass
height; the grass height
to be cut must be less
than 10 cm)
Set higher cutting height
I
.
Convert mower to rear
ejection
U2
+
S1
and mow
lawn with high cutting height
first.
Driving speed too high.
Adapt driving speed, switch
motor drive off if necessary.
Grass accumulation
under the mower blade.
Set higher cutting height
I
.
Insufficient overlap
between mowing lanes.
If grass is long, the mowing
lanes may need to overlap
further.
Grass is damp.
Set higher cutting height
I
.
Allow the lawn to dry.
Repairs to electrical machines must always be performed only by qualified electricians.
Please do not repair them yourself.
In the case of faults and defects which have not been listed here, please contact the
nearest authorized dealer. This applies in particular to appliances with electrical motors,
as when these are repaired they must always undergo an insulation protection test.
Your authorized dealer will also help you if you do not wish to perform any of the
maintenance work described here yourself.
19
TECHNICAL DATA
Motor
Motor
Alternating current motor
Connection voltage
230 V
Power
1700 W
Motor speed
3000 min
-1
Mower
Housing
Die-cast aluminium
Cutting width
430 mm
Cutting heights
Central, (15), 25, 30, 40, 45, 55, 60, 70, 80 mm
Adjustable-height handlebar
3-way
Grass collector capacity
65 litres
Speed
2,4
–
3,6 km/h
Weight
35 kg
Length
1565 mm
Width
500 mm
Height
1025 mm
Wheels front / rear
Ø 180 mm / Ø 200 mm
Bearing front
Cup-and-cone bearing
Bearing rear
Cup-and-cone bearing
Sound power level
Guaranteed sound power level;
measured according to 2000/14/EC
L
wa
= 96 dB(A)
Sound pressure level
Emission sound pressure level at operator's workplace;
measured according to EN60335-2-77
Measuring inaccuracy; according to ISO 4871
L
pA
= 82 dB(A)
1.5 dB
Vibrations
Vibrations on the lawnmower’s
handlebar;
measured according to EN60335-2-77
Measuring inaccuracy; according EN12096
a
hW
= 2.5 m/s
2
1.3 m/s
2
20
ORIGINAL SPARE PARTS
Conversion kit for mulching system
BSA632
Roller bearing grease
SAA11300
Cutter bar
For safety reasons, the cutter bar must
always be replaced by an authorised
workshop.
This workshop has the respective spare
part numbers for the cutter bar available.
Содержание 43-EL VARIO
