S+S Regeltechnik Rymaskon 200-Modbus Series, Руководство пользователя

Страница: 37 / 55

RYM ASKON
®
200-Modbus
Modbus Slave User Manual
© S+S REGELTECHNIK GMBH
| THURN-UND-TAXIS-STR.22 | 90411 NÜRNBERG | GERMANY | FON +49(0)911 519470 | www.SplusS.de
Page 37 of 55
Register Name
Register
Adresse
Bit Position
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
config_set_
point _12
344
0x0158
unit_modbus
[0x0]
unit
[0x0]
PIN
[0]
semantic_meaning
[0x00]
345
0x0159
VSA
[0]
VEU
[0]
ESA
[0]
EEU
[0]
[0]
[0] [0]
[0] [0] [0]
[0]
[0] [0] [0] [0] [0]
config_set_
point _13
346
0x015A
unit_modbus
[0x0]
unit
[0x0]
PIN
[0]
semantic_meaning
[0x00]
347
0x015B
VSA
[0]
VEU
[0]
ESA
[0]
EEU
[0]
[0] [0] [0] [0] [0] [0] [0] [0] [0] [0] [0] [0]
config_set_
point _14
348
0x015C
unit_modbus
[0x0]
unit
[0x0]
PIN
[0]
semantic_meaning
[0x00]
349
0x015D
VSA
[0]
VEU
[0]
ESA
[0]
EEU
[0]
[0]
[0] [0]
[0] [0] [0]
[0]
[0] [0] [0] [0] [0]
config_set_
point _15
350
0x015E
unit_modbus
[0x0]
unit
[0x0]
PIN
[0]
semantic_meaning
[0x00]
351
0x015F
VSA
[0]
VEU
[0]
ESA
[0]
EEU
[0]
[0]
[0] [0]
[0] [0] [0]
[0]
[0] [0] [0] [0] [0]
These registers hold the configuration for the 16 set point.
!!! For both, unit and unit_modbus the following values are possible:
0x0 0x1 0x2 0x3 0x4 0x5 0x6 0x7 0x8 0x9 0xA 0xB 0xC
no
unit
°C °F cfm l/s m³/h Pa inWC V % %RH ppm °F dec.
Bits 0-11 of the higher address of each configuration register indicate the symbols that are displayed along
with the corresponding display value.
These two bits define if the set point is editable for the end user and/or the system administrator. The
following states are valid:
These two bits define if the set point is visible for the end user and/or the system administrator. If set to ‘1’ the
set point will be visible.
!!! See Table 30 on Page 40 for example configurations of display values or set points.
semantic_meaning:
is used to provide information about the semantic meaning of the set point.
For further information please see Table 29 on Page 38.
PIN:
if set to ‘1’ the the corresponding set point is pincode protected and can only
be changed in EDIT-mode if the correct pincode has been entered before.
unit:
defines a unit with which the corresponding set point appears on the LCD
unit_modbus:
defines a unit that the corresponding set point register appears on Modbus
EEU: Editable for End User
ESA: Editable for Aystem Administrator
0 – defines that the set point is not editable.
VEU : Visible for End User
VSA : Visible for System Administrator
1 – editable for system administrator.
Table 28: Set Point Configuration